110798 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Got heat only on start of cycle and no repeat of flame. Suspected coils on gas valve.
18 of 20 people
found this instruction helpful.
-
John T Lundy from Pittsburgh, PA
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
I used a multi meter to find coils failed in warmed temperature condition.
I tested main switch for different cycle operation. Main switch was worn out inside and not making good contact for soft cycles.
This dryer is 25 years old. I chose to replace all the sensors, fuses, ignitor, gas valve coils, cycle switch and thermostat. ... Read more
This was cost effective for me, because now, I actually have a good dryer that might just last another 25 years. I might replace the drive belt soon. I'll order from Parts Select. This was easy and fun. Thanks!
I tested main switch for different cycle operation. Main switch was worn out inside and not making good contact for soft cycles.
This dryer is 25 years old. I chose to replace all the sensors, fuses, ignitor, gas valve coils, cycle switch and thermostat. ... Read more
This was cost effective for me, because now, I actually have a good dryer that might just last another 25 years. I might replace the drive belt soon. I'll order from Parts Select. This was easy and fun. Thanks!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Insanely loud squeaking
17 of 17 people
found this instruction helpful.
-
Stacy B. from MUKWONAGO, WI
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
With the correct parts and watching the video, it was so easy to repair. We ordered the wrong part (for the Electric Dryer when it should have been for the Residential Dryer) but the return was easy and we got the new parts super fast. Next time I would probably look at the offending part first before ordering just to make certain. But w
... Read more
e used a socket set and Philips screwdriver and actually had our teens do all the work for experience. Fixed the loud noise one and for all.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer drum was not turning when started.
17 of 18 people
found this instruction helpful.
-
Dennis from AUSTIN, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I moved the dryer to a location where I could get to both the front and back sides. I opened the back by first removing the top cover and then the back. It requires either a Phillips head screwdriver or a quarter inch socket. In addition, it requires removing the four power wires which connect to the computer. If you are unfamiliar with t
... Read more
he wiring layout, take a photo with your cell phone which you can then refer to when re-assembling. Once the back was removed, I saw that the belt was still intact, but the pulley which provides tension to the belt was frozen. Take a photo of the belt route between the motor and the pulley. Try to get the spring position in the photo. Remove the belt from the pulley by reducing the tension and then sliding the belt out (this assumes the belt is not broken). The pulley arm is held in place by a single bolt which can be removed by a socket set. Remove the arm with the pulley attached. Examine the pulley to figure out why it is frozen. In my case, the pulley had been frozen for some time and the belt had actually chewed through the pulley and was sliding (polishing) on the pulley axle? I used a pair of pliers to loosen the destroyed pulley by rotating it back and forth over the axle while gripping the arm the axle is attached to. As it loosened up I worked it off the axle. I used a cloth to clean the axle of grime from the belt, pulley, and dryer lint. The new pulley comes with a washer and triangular plastic "fastener". First you put on the washer, then the pulley and then you secure it on the axle by sliding the triangular fastener over the axle so it sits in a small grove near the end of the axle. Then put the pulley arm back by replacing the bolt. Make sure you do not overtighten the arm since it is intended to rotate about the bolt. If the dryer belt breaks, the spring will pull the arm down and throw a cutoff switch. Its operation should be obvious. Once the arm is back in place, refer to your photo and replace the spring (this can be tricky and frustrating, particularly if you don't use something like needle nose pliers). Once the spring is in place, depress it and re-install the dryer belt. Refer to the photo you took earlier if you've forgotten how the belt was routed. Then re-install the dryer's back panel, re-attach the electric wires (again refer to the photo you took earlier), and re-attach the top cover. You might want to test your handiwork at this point before you reconnect the dryer vent
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken push to stat switch
18 of 21 people
found this instruction helpful.
-
Charles from Fairfax, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed back cover, removed broken switch, replaced with new switch, replaced back cover, told wife her dryer was fixed.
Was this helpful?
Thank you for voting!
dryer not working
22 of 33 people
found this instruction helpful.
-
Maura from Newtown, CT
- Really Easy
- Less than 15 mins
After unplugging and removing the back cover from the dryer, locate the push button switch. Slide putty knife around outer cover to unhook catch. Replace with new push button switch. My dryer is still not working, but this was a simple replacement.
Was this helpful?
Thank you for voting!
idler pully sqwieling
19 of 24 people
found this instruction helpful.
-
Jerry Duty from Fort Walton Beach, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
once the back is off remove belt from tentioner and remove v clip. smooth shaft with wd-40 and scotch brite , then install new idler replace v clip
and your done !!!
and your done !!!
Was this helpful?
Thank you for voting!
parts took more than two months to get here.
17 of 19 people
found this instruction helpful.
-
rodney from Mad River, CA
- Very Difficult
- More than 2 hours
I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful
Other Parts Used:
Was this helpful?
Thank you for voting!
The felt strip on the filter had come undone.
21 of 31 people
found this instruction helpful.
-
Rebecca from Laredo, TX
- Really Easy
- Less than 15 mins
Took the old filter out and inserted the new one- works great!!
Was this helpful?
Thank you for voting!
Dryer starts with loud squeak initially. Eventually there was a loud clank and dryer stopped.
16 of 17 people
found this instruction helpful.
-
Victor from HOUSTON, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Rather than remove the front panels, door, control panel and drum, I noticed 1/4" metal screws on the back panel. There were approximately 6 holding the back panel in place. I did have to remove the top panel as well before removing the back. Once removed I had complete access to the broken idler pulley assembly. I immediately saw the b
... Read more
roken pulley. I installed the new one with very little effort. Reset the belt according to instructions from the video. Reassembled, plugged in, hit start and enjoyed the sweet sounds of success. All told it took me about 20 minutes from start to finish.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer continued to run with door open
18 of 23 people
found this instruction helpful.
-
Colleen from CAPE CORAL, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
The video provided by this site on YouTube on this topic was perfect. Saved us a couple of hundred dollars DIY rather than repair man.
Was this helpful?
Thank you for voting!
part number was different from the original, but it fit just fine.
20 of 30 people
found this instruction helpful.
-
John from Bristol, CT
- Easy
- Less than 15 mins
installed the new dryer lint screen, it fit perfectly
and is now in operation.
and is now in operation.
Was this helpful?
Thank you for voting!
Change dryer belt
15 of 17 people
found this instruction helpful.
-
Scott from Bayport, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I p
... Read more
opped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.
Read less
Was this helpful?
Thank you for voting!
seal for lint filter came off
17 of 23 people
found this instruction helpful.
-
John from Midland, TX
- Really Easy
- Less than 15 mins
Pulled out the old and slid in the new filter
Was this helpful?
Thank you for voting!
Door catch on dryer door broke
14 of 14 people
found this instruction helpful.
-
Lynne from Jamestown, CA
- Really Easy
- Less than 15 mins
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might c
... Read more
ontact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.
Read less
Was this helpful?
Thank you for voting!
Loud banging noise when running dryer
15 of 18 people
found this instruction helpful.
-
Joseph from Prospect Park, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Found one of the two drum support rollers was badly worn. Found Partselect.com, found my parts in less then 2 mins. Figured that I was in there so I should just replace the belt so I got one of those also. Parts arrived in 3 days dryer as good as new in 20 mins.
Other Parts Used:
Was this helpful?
Thank you for voting!