110797 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burner would not go on on my Stack Set Dryer
16 of 24 people
found this instruction helpful.
-
Robert from North East, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front
... Read more
cover screws. Piece of Cake!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Lint has been bypassing the lint filter and building up in the fan (and duct)
12 of 12 people
found this instruction helpful.
-
David from PINETOWN, NC
- Really Easy
- Less than 15 mins
I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan
... Read more
wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.
Read less
Was this helpful?
Thank you for voting!
Dryer door switch
12 of 13 people
found this instruction helpful.
-
Frank from STANFORDVILLE, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers
We watched the video on ur website! Thank you
Was this helpful?
Thank you for voting!
No Heat
18 of 31 people
found this instruction helpful.
-
stacy m from akron, OH
- Really Easy
- 30 - 60 mins
-
Nutdriver
First time ever repaired anything let alone a dryer, I watch the video and followed instructions, was pretty simple, Works like a charm
Other Parts Used:
Was this helpful?
Thank you for voting!
Defective Door Switch
12 of 13 people
found this instruction helpful.
-
George from Bedford, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Opened the lid and removed screws hollding switch to cabinet. Had to use magnifying glass to find locking mechanism on the electrical harness. Used small bladed screwdiver from my computer maintenaqnce kit to disengae lock. Hooked up harness. Replaced screws and shut lid. Main difficulty is my near vision. Requires use of a magnifier I a
... Read more
m 80 years old). Your video is great. Gives step by step instructions.
Read less
Was this helpful?
Thank you for voting!
Rear dryer drum seal came out
17 of 29 people
found this instruction helpful.
-
William from Pontiac, MO
- Easy
- More than 2 hours
-
Screw drivers, Socket set
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Was this helpful?
Thank you for voting!
Door latch (female part) was broken.
11 of 11 people
found this instruction helpful.
-
JEANMARIE from BELLEROSE, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
The Dryer would not get hot.
14 of 20 people
found this instruction helpful.
-
Jerry from Bradenton, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.
Other Parts Used:
Was this helpful?
Thank you for voting!
dryer not heating up
12 of 14 people
found this instruction helpful.
-
Richard from New Windsor, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helpi
... Read more
ng me out!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The dryer was not fully drying
12 of 14 people
found this instruction helpful.
-
Michael from Chicago, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I
... Read more
will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.
Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.
Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
dryer would not turn off when the door is open
10 of 10 people
found this instruction helpful.
-
James from Webster, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
it took loess than 10 minutes to change the door switch after watching the repair video
Was this helpful?
Thank you for voting!
Timer not advancing
10 of 10 people
found this instruction helpful.
-
Barb from SHARPSVILLE, PA
- Very Easy
- 15 - 30 mins
-
Nutdriver
Timer-Removed the screws from top back panel from behind the dryer. Removed the screws on timer. Replaced one wire connection at a time. Remounted timer and put panel back on.
Thermal fuse- also because it seams to fail a lot and I was already working on the dryer. Removed lower back panel. Found fuse. Unscrewed the one screw ... Read more . Disconnected fuse and put new one in. Kept old one as a back up.
Total time between replacing the thermal fuse and the timer-1/2 hr.
A little pricey, but the dryer is only 3 yrs old and I was able to fix it! Hope it will last us for several years.
Thermal fuse- also because it seams to fail a lot and I was already working on the dryer. Removed lower back panel. Found fuse. Unscrewed the one screw ... Read more . Disconnected fuse and put new one in. Kept old one as a back up.
Total time between replacing the thermal fuse and the timer-1/2 hr.
A little pricey, but the dryer is only 3 yrs old and I was able to fix it! Hope it will last us for several years.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer Would Not Start.
11 of 13 people
found this instruction helpful.
-
GALEN from NEDERLAND, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Partselect order confirmation email included video instructions of how to change the door switch on my model dryer. Like others I had a pause with the switch connector. I viewed the video again and the instrucions showed to use the putty knife tip to push down on the connector tabs and it came right off. Replacing the switch was easy a
... Read more
s the video instructions. Fast shipping of the right part at a good price. The video was pricless. Thank you partselect.
Read less
Was this helpful?
Thank you for voting!
would not stop when opening door during cycle
10 of 11 people
found this instruction helpful.
-
PHILIP from MATTHEWS, NC
- Really Easy
- 30 - 60 mins
-
Screw drivers
Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to
... Read more
take the time to remove dust and lint from behind the dryer. Easy repair.
Read less
Was this helpful?
Thank you for voting!