110786 Kenmore Dryer - Instructions

All Instructions for the 110786
106 - 120 of 2122

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer worked but no heat
18 of 20 people found this instruction helpful.
  • Tracie from Culver City, CA
  • A Bit Difficult
  • 15 - 30 mins
Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.
Was this helpful?
Thank you for voting!
Drum was binding because of worn bearing supporting front of dryer drum
23 of 35 people found this instruction helpful.
  • Leslie from Townsend, GA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to gl ue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!!
Was this helpful?
Thank you for voting!
Got heat only on start of cycle and no repeat of flame. Suspected coils on gas valve.
18 of 20 people found this instruction helpful.
  • John T Lundy from Pittsburgh, PA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench set
I used a multi meter to find coils failed in warmed temperature condition.
I tested main switch for different cycle operation. Main switch was worn out inside and not making good contact for soft cycles.
This dryer is 25 years old. I chose to replace all the sensors, fuses, ignitor, gas valve coils, cycle switch and thermostat.
This was cost effective for me, because now, I actually have a good dryer that might just last another 25 years. I might replace the drive belt soon. I'll order from Parts Select. This was easy and fun. Thanks!
Was this helpful?
Thank you for voting!
The Dryer would not start
17 of 18 people found this instruction helpful.
  • Dennis from Redondo Beach, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First and most important was to unplug the unit.
I removed the 2 screws that hold the lint screen shoot to the top cover and then simply popped the top of the machine open using 2 screw drivers and
gently prying it up. I raised the top cover about 8 inches and supported it with a block of wood.
I opened the front loading do or and removed the 2 screws that hold the door actuator switch while holding the switch on the inside so that nothing would fall down into no mans land. Once the switch was loose I pulled it into view and could see that the actuator spring was broken. I used the search at the Part Select Web site and found the placement part very easy. I was amazed that the part was shipped and delivered to my house the very next day. The actuator spring simply snaps into place and I assembled it in the reverse order of removal, I removed the block of wood and snapped the top back into location and reinstalled the 2 screws for the lint screen shoot . I plugged the dryer in and it work perfect. I can't say enough about how well the experiance with Parts Select went, I will recommend them to others.
Was this helpful?
Thank you for voting!
dryer sounded like I was strangling a dog
18 of 21 people found this instruction helpful.
  • Lynda from Syracuse, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First, I watched a utube video of replacing the dryer belt. Then I went to Sears Hardware and couldn't find a part. Then I ordered the parts for my favorite online repair parts source - partselect.com. I had the part in one day! We did exactly what the video showed and also replaced the two wheels that looked like roller blade wheels. Pie ce of cake. Saved a $75 repair call plus whatever the parts would have been and spent about 20 minutes doing it. Back in business. Great for a 12 year old dryer! Buy the dryer kit!
Was this helpful?
Thank you for voting!
Squeaky Dryer
17 of 19 people found this instruction helpful.
  • Daniel from Hamilton, OH
  • Easy
  • 15 - 30 mins
  • Screw drivers
I looked for squeaky dryer within parts select and went with the 80%. I received the Maintenance Kit, replaced two rollers and it works like new. Amazing since this is the first time I have ever opened a dryer. The instruction sheet and parts were all I needed.
Was this helpful?
Thank you for voting!
Dryer continued to run with door open
18 of 23 people found this instruction helpful.
  • Colleen from CAPE CORAL, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The video provided by this site on YouTube on this topic was perfect. Saved us a couple of hundred dollars DIY rather than repair man.
Was this helpful?
Thank you for voting!
Loudly clunking clothes drum due to worn out roller
17 of 20 people found this instruction helpful.
  • KENNETH from WEST ORANGE, NJ
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Followed video on Parts Select site for comparable model showing roller and drive belt replacement.

The triangle plastic retaining clips were the most difficult part , to put
on and take off. They required careful , firm stretching with needle nose pliers.
Was this helpful?
Thank you for voting!
Rear Drum Seal started to come apart
16 of 18 people found this instruction helpful.
  • Brett from CRESCENT CITY, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Used the YouTube video sent by this site
Was this helpful?
Thank you for voting!
Washer will agitate, but won't spin
18 of 24 people found this instruction helpful.
  • Mandie from Lewisville, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I ordered the switch, which is what most people told me the problem was. I didn't have a multimeter, so I couldn't test the current one.

I removed the two screws from above the lid switch, removed the control panel screws on either side, and used a flat screwdriver to pry the top off by popping the clips.

The swit ch was easy to reach, and I compared the old and new switch after removing the paddle assembly. The new switch has three prongs, whereas my old one had two, so I put the gray wire terminal onto the bottom prong. I set everything down, plugged it in, and tested it, but still no spin cycle.

After some further research, I realized the problem was with the spin solenoid under the washer, or the red wire that leaves the lid switch and goes to the spin solenoid, also called a wig-wag solenoid. (This is a belt driven model, not direct drive.) It's not too common that the solenoids fail, but it is rather common that the wires break inside the insulation on this model.

Moral of the story is always ohm through the switches and wires before ordering replacement parts. (Remember, never ohm through a live circuit.)
Was this helpful?
Thank you for voting!
One day, I found my dryer continued running after I opened the door. And next day, it stopped working at all. I thought it was time to buy a new one, since my dryer had been used for more than 15 years. But I was curious to know what went wrong, and recalled my friend told me he repaired the door
17 of 21 people found this instruction helpful.
  • Xiaobin from Cordova, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
My daughter found the video on youtube, which showed step by step repairing procedures. I just followed it and fixed my dryer in 15 min.
Was this helpful?
Thank you for voting!
part number was different from the original, but it fit just fine.
20 of 30 people found this instruction helpful.
  • John from Bristol, CT
  • Easy
  • Less than 15 mins
installed the new dryer lint screen, it fit perfectly
and is now in operation.
Was this helpful?
Thank you for voting!
Dryer kept spinning when the door opened
16 of 18 people found this instruction helpful.
  • Gary from Ocean Springs, MS
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Came to Parts Select. Looked for door switch. Read what other people did. Part came in a few days took a few minutes to take old switch out (had to pry the plastic connection apart with little thin screwdriver). Everything was easy
Was this helpful?
Thank you for voting!
Lint screen torn
15 of 16 people found this instruction helpful.
  • James from Glenside, PA
  • Really Easy
  • Less than 15 mins
Lint screen on my 30-year dryer was torn. Ordered the new screen here with just the part number, fits well. Very helpful website.
Was this helpful?
Thank you for voting!
Door catch on dryer door broke
14 of 14 people found this instruction helpful.
  • Lynne from Jamestown, CA
  • Really Easy
  • Less than 15 mins
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might c ontact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.
Was this helpful?
Thank you for voting!
All Instructions for the 110786
106 - 120 of 2122