1107849 Kenmore Dryer - Instructions

All Instructions for the 1107849
61 - 75 of 342

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Start and then kick out.
5 of 9 people found this instruction helpful.
  • PHILLIP from AUSTIN, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Was this helpful?
Thank you for voting!
Dryer would not run
4 of 6 people found this instruction helpful.
  • james from york, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
Was this helpful?
Thank you for voting!
Gasket was falling off, needed replacement
4 of 6 people found this instruction helpful.
  • Anthony from N. Ferrisburg, VT
  • Really Easy
  • Less than 15 mins
Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.
Was this helpful?
Thank you for voting!
broken air filter
3 of 3 people found this instruction helpful.
  • Martin from CATHEDRAL CTY, CA
  • Very Easy
  • Less than 15 mins
I would not ever consider this a repair. The dryer filter cracked because of my wife put it in loosely. The new one just fit right in.
What was so good about the entire process was how quickly I recieved the part. A matter of two days.
Was this helpful?
Thank you for voting!
Broken dryer lint trap
3 of 3 people found this instruction helpful.
  • Amy from ANNANDALE, MN
  • Very Easy
  • Less than 15 mins
Excellent and super easy. Owned the box and snapped the new one in. Ready for laundry again in a matter of minutes.
Was this helpful?
Thank you for voting!
Lint Filter and Cover Missing
3 of 3 people found this instruction helpful.
  • Maxine from FORT WORTH, TX
  • Really Easy
  • Less than 15 mins
Didn't need a repairman for this project! Ordered the part (seems like on Sunday) and got it really quick (the next Wednesday). Opened the package, placed the part where it was supposed to go and shazam!!!! Fixed it was quick and easy!
Was this helpful?
Thank you for voting!
a broken belt
6 of 12 people found this instruction helpful.
  • Dorise from Donalsonville, GA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable)
my hany man did it....
Was this helpful?
Thank you for voting!
The drum made a lot of noise while turning. The dryer shook
3 of 3 people found this instruction helpful.
  • Craig from VASS, NC
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
Was this helpful?
Thank you for voting!
Dryer drum wouldn't turn and motor would shut off
3 of 4 people found this instruction helpful.
  • Cynthia M from Westfield, MA
  • Easy
  • More than 2 hours
  • Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Was this helpful?
Thank you for voting!
door switch lever/latch broke
3 of 4 people found this instruction helpful.
  • Ed from Charlottesville, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating elemen t, and other parts. At some point it will be time for a new dryer...
Was this helpful?
Thank you for voting!
Dryer door actuator lever broke
3 of 4 people found this instruction helpful.
  • Mark from Clarksburg, MD
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. R einstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people found this instruction helpful.
  • WILFRED from NORTH HIGHLANDS, CA
  • Really Easy
  • Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people found this instruction helpful.
  • Raymond from Washington, DC
  • Really Easy
  • Less than 15 mins
  • Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 4 people found this instruction helpful.
  • Wayne from Rosenberg, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.
Was this helpful?
Thank you for voting!
Lint trap was warped and would not stay in the opening.
3 of 4 people found this instruction helpful.
  • Carmella from THONOTOSASSA, FL
  • Very Easy
  • 15 - 30 mins
Easy for a 87 year old.I just snapped the cover to the filter basket and then inserted the whole basket into the
Was this helpful?
Thank you for voting!
All Instructions for the 1107849
61 - 75 of 342