110775 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dead motor
17 of 24 people
found this instruction helpful.
-
Robert from Glencoe, IL
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
1. Shut off gas and disconnected dryer.
2. Opened cabinet. Easy sheet metal screws and fairly obvious how everything goes together. NB: You'll need a block (or a helper to hold things while you run to look for one) to hold the drum while removing the front.
3. The motor is connected with a single harness, so wiring is a snap ... Read more .
4. Removing the blower wheel from the back was hard. I braced the motor shaft and turned with all the leverage I could muster, but it was stuck. Plan B: Recip saw to cut the shaft. Motor comes out one side and the fan comes out the other.
5. The fan, of course, was unusable because there was still a piece of motor shaft stuck in the thread. This is why I had to spring for a new wheel.
6. Put everything back together and receive wife's adoring praise...
2. Opened cabinet. Easy sheet metal screws and fairly obvious how everything goes together. NB: You'll need a block (or a helper to hold things while you run to look for one) to hold the drum while removing the front.
3. The motor is connected with a single harness, so wiring is a snap ... Read more .
4. Removing the blower wheel from the back was hard. I braced the motor shaft and turned with all the leverage I could muster, but it was stuck. Plan B: Recip saw to cut the shaft. Motor comes out one side and the fan comes out the other.
5. The fan, of course, was unusable because there was still a piece of motor shaft stuck in the thread. This is why I had to spring for a new wheel.
6. Put everything back together and receive wife's adoring praise...
Read less
Was this helpful?
Thank you for voting!
Noisy Dryer/Rear Seal Came off
14 of 15 people
found this instruction helpful.
-
Charles from Olney, MD
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
So the first thing I did was search the web for the parts and came to this site. I knew the model and that I needed rollers and a rear seal. I found both on this site for order in less than 10 minutes, which included finding the wonderful diagrams and directions for replacing the parts. I placed the order got the parts two days later.
... Read more />
I printed out the directions to take the drum out and followed them. After unplugging the dryer, I pushed in the clips that were indicated to release the top and pushed that up. I then disconnected the door switch. I reached under the dryer (not having a kicker panel for some years...) and worked to release the belt. I then took the front off removing the four screws as described. The drum removal was a little more awkward than I had anticipated, but came out without major hassle. Getting the drive belt off was the worst part other than the size.
I then removed the warn rollers after taking the clips off with a pair of needle nose pliers. I put the new rollers on and secured them.
I then went to the drum.After cleaning it a bit, I attempted to dry fit the seal onto the drum to get the idea of how it would fit. This didn't work easily as the seal needed to stretch a bit more than it could while staying on all around. I grabbed a couple of clamps and worked it on using those. Once that was sorted I started to apply the glue. It was more runny than I had anticipated. After working that around the seal I let it dry overnight to an excellent bond.
The next day I put the drum back in, adjusted the seal properly and put the machine back together. The tension roller is not fixed to the machine so getting that back on was a little bit of a trick but was overcome easily enough.
A few loads of laundry later and I knew it was all done and working OK. It hasn't dried this good or been this quiet in years.
This was my first major appliance repair. With the assistance of the diagrams on here and directions I would say to anyone contemplating a diy repair on something like this to give it a shot.
My only recommendation to the site is to more visibly recommend doing the seals, rollers and drive belt at the same time. While in there I could see wear on the drive belt and will probably need to replace that in the next six months or so.
... Read more />
I printed out the directions to take the drum out and followed them. After unplugging the dryer, I pushed in the clips that were indicated to release the top and pushed that up. I then disconnected the door switch. I reached under the dryer (not having a kicker panel for some years...) and worked to release the belt. I then took the front off removing the four screws as described. The drum removal was a little more awkward than I had anticipated, but came out without major hassle. Getting the drive belt off was the worst part other than the size.
I then removed the warn rollers after taking the clips off with a pair of needle nose pliers. I put the new rollers on and secured them.
I then went to the drum.After cleaning it a bit, I attempted to dry fit the seal onto the drum to get the idea of how it would fit. This didn't work easily as the seal needed to stretch a bit more than it could while staying on all around. I grabbed a couple of clamps and worked it on using those. Once that was sorted I started to apply the glue. It was more runny than I had anticipated. After working that around the seal I let it dry overnight to an excellent bond.
The next day I put the drum back in, adjusted the seal properly and put the machine back together. The tension roller is not fixed to the machine so getting that back on was a little bit of a trick but was overcome easily enough.
A few loads of laundry later and I knew it was all done and working OK. It hasn't dried this good or been this quiet in years.
This was my first major appliance repair. With the assistance of the diagrams on here and directions I would say to anyone contemplating a diy repair on something like this to give it a shot.
My only recommendation to the site is to more visibly recommend doing the seals, rollers and drive belt at the same time. While in there I could see wear on the drive belt and will probably need to replace that in the next six months or so.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Time clock not moving .Not enough heat
16 of 21 people
found this instruction helpful.
-
PHILIP from LONG ISLAND CITY, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Was this helpful?
Thank you for voting!
Drum not turning; accompanied by loud "screeching" sound.
15 of 19 people
found this instruction helpful.
-
holly from LONG BCH TWP, NJ
- Easy
- 30 - 60 mins
-
Socket set, Wrench (Adjustable)
Followed instructional video provided for this type of repair after diagnosing problem via of 'troubleshooting' on PartsSelect site. Simple, safe, and relatively easy (minimal mechanical knowledge helpful).
Second time using PartSelect; washing machine repair ~ 6 mo. previous.
PartSelect was spot-on with that repair as well, sa ... Read more ving hundreds of dollars.....my go-to site for appliance repairs and pats....make it yours as well and you will NOT be disappointed! Fast, prompt shipping.
Second time using PartSelect; washing machine repair ~ 6 mo. previous.
PartSelect was spot-on with that repair as well, sa ... Read more ving hundreds of dollars.....my go-to site for appliance repairs and pats....make it yours as well and you will NOT be disappointed! Fast, prompt shipping.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would leave clothes damp
15 of 20 people
found this instruction helpful.
-
Luke from Elmira, NY
- Easy
- Less than 15 mins
-
Nutdriver
First, I unplugged the dyer and then I removed all of the screws for the panel that covers the rear of the dryer. This exposed the cycling thermostat's location. I then removed the wires, one at a time so I would be able to put them back on in the same place. Then I removed the one screw using a nut driver and then put the new cycling the
... Read more
rmostat in place. It was pretty easy.
Read less
Was this helpful?
Thank you for voting!
door cables broke
16 of 23 people
found this instruction helpful.
-
CAROL from HUNTINGDON, PA
- Easy
- Less than 15 mins
-
Screw drivers
Removed the screws holding the dryer door together and pushed the plastic pin out that the cable end went through. removed the screws at the dryer filter then popped up the top. put the cable through the door and then reached down with the door spring and went through the hole in the cable end, fastened the spring and pushed back down the
... Read more
top and replaced all screws. job complete. the hardest part was getting the spring through the small hole on the cable end but with a little patience and persistance it was accomplished.
Read less
Was this helpful?
Thank you for voting!
drum very loud when rotating
13 of 15 people
found this instruction helpful.
-
michael from indianapolis, IN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and repl
... Read more
aced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.
Thanks Mike
It was a very simple repair.
Thanks Mike
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
squeaky and very loud noise
13 of 15 people
found this instruction helpful.
-
Jimmie from Lucerne Valley, CA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
first we printed out directions from a couple of online repair sites that had pictures.
We followed the directions to remove the front of the dryer and removed the belt off the drier and then took out the drum. We had a hard time trying to keep the rear seal on so used CLOTHES PINS to put on the seal, then we added the adhesive repla ... Read more cing the clothes pins until the whole seal glued. Since the drum was already out, we put it in the sun to really dry the glue.
Next we attacked the drum support rollers. We removed the back of the dryer and used a 9/16" socket with an extention to remove the back nuts.
We took out the shaft, used sandpaper on it and then replaced the triangle clips and the support rollers.
Then put the back on again, then the front, making
sure the drum fit on the front. You have to then figure out the belt, with the rubber side down, and then work with the tensioner, which took my poor husband a while. Then lowered the top, put the clips back on and the bottom, making sure we turned the drum. It was a success after about 3 hours. You can do it a lot easier with pictures.
We followed the directions to remove the front of the dryer and removed the belt off the drier and then took out the drum. We had a hard time trying to keep the rear seal on so used CLOTHES PINS to put on the seal, then we added the adhesive repla ... Read more cing the clothes pins until the whole seal glued. Since the drum was already out, we put it in the sun to really dry the glue.
Next we attacked the drum support rollers. We removed the back of the dryer and used a 9/16" socket with an extention to remove the back nuts.
We took out the shaft, used sandpaper on it and then replaced the triangle clips and the support rollers.
Then put the back on again, then the front, making
sure the drum fit on the front. You have to then figure out the belt, with the rubber side down, and then work with the tensioner, which took my poor husband a while. Then lowered the top, put the clips back on and the bottom, making sure we turned the drum. It was a success after about 3 hours. You can do it a lot easier with pictures.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
dryer door would not latch
13 of 15 people
found this instruction helpful.
-
Robert from Livermore, ME
- Really Easy
- Less than 15 mins
my dryer door didn't latch for over a year. We were accustom to proping large objects against it. a friend told me to look on line. The close up pictures and parts diagrams were awesome. It was here in 4 days . Now my family thinks I am a hero. The end
Was this helpful?
Thank you for voting!
Burner would not go on on my Stack Set Dryer
16 of 24 people
found this instruction helpful.
-
Robert from North East, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front
... Read more
cover screws. Piece of Cake!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
the drum was not turning because a broken belt
14 of 19 people
found this instruction helpful.
-
thomas from bloomfield, NJ
- Easy
- 15 - 30 mins
-
Screw drivers
I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum expo
... Read more
sed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.
Read less
Was this helpful?
Thank you for voting!
Defective Door Switch
12 of 13 people
found this instruction helpful.
-
George from Bedford, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Opened the lid and removed screws hollding switch to cabinet. Had to use magnifying glass to find locking mechanism on the electrical harness. Used small bladed screwdiver from my computer maintenaqnce kit to disengae lock. Hooked up harness. Replaced screws and shut lid. Main difficulty is my near vision. Requires use of a magnifier I a
... Read more
m 80 years old). Your video is great. Gives step by step instructions.
Read less
Was this helpful?
Thank you for voting!
Dryer door switch
12 of 13 people
found this instruction helpful.
-
Frank from STANFORDVILLE, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers
We watched the video on ur website! Thank you
Was this helpful?
Thank you for voting!
No Heat
18 of 31 people
found this instruction helpful.
-
stacy m from akron, OH
- Really Easy
- 30 - 60 mins
-
Nutdriver
First time ever repaired anything let alone a dryer, I watch the video and followed instructions, was pretty simple, Works like a charm
Other Parts Used:
Was this helpful?
Thank you for voting!
Quick and simple - quickest $100 I've ever saved!
13 of 16 people
found this instruction helpful.
-
Kelly from Waukegan, IL
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Removed the two screws under the lint trap
Opened the top (had to use flathead screwdriver to release latches)
Disconnected door switch harness from front panel
Removed 2 screws holding front panel on dryer
Lifted out dryer drum (previous belt had broken)
Vacuumed inside of dryer (found $3 in quarters!)
Put n ... Read more ew belt around drum
Put drum back in dryer, using empty laundry soap bottle to support its weight
Looped belt around pulley and motor; secured pulley to dryer bottom
Made sure rear gasket thingy was aligned properly and drum turned freely
Put front panel back on
Re-attached door switch
Closed top and put screws back in under lint trap
Fired it up - WOOHOO!
Opened the top (had to use flathead screwdriver to release latches)
Disconnected door switch harness from front panel
Removed 2 screws holding front panel on dryer
Lifted out dryer drum (previous belt had broken)
Vacuumed inside of dryer (found $3 in quarters!)
Put n ... Read more ew belt around drum
Put drum back in dryer, using empty laundry soap bottle to support its weight
Looped belt around pulley and motor; secured pulley to dryer bottom
Made sure rear gasket thingy was aligned properly and drum turned freely
Put front panel back on
Re-attached door switch
Closed top and put screws back in under lint trap
Fired it up - WOOHOO!
Read less
Was this helpful?
Thank you for voting!