All Installation Instructions for Kenmore Dishwasher 110773882

The coating on the upper rack had rust coming through.

Removed the plugs in the slides, removed the rack, slid the new rack in and replaced the plugs.

Parts Used:

Dishwasher Upper Dishrack w/Middle Arm And Tube

Ernie from Salinas, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

dish washer leaking

Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.

Parts Used:

Dishwasher Door Gasket - Gray

Gary from Winnemucca, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

The top drawer wash rotor hose was leaking badly and as a result allowed uneven water flow to the upper drawer of the dishwasher.

I first had to take the upper drawer of the dishwasher out so that I could get to the faulty part. This was a little tricky as there were two clips that had to be removed from the arm slides before the upper drawer could be removed.
I then realized that the faulty part DID NOT exactly match the repair part I received. The original connection wand was in two pieces where the repair part was all one piece. That required a bit of thought before I began the repair. There was NO drawing accompanying the new part, so I had to decide how the part would be connected. After a little trial and error, I determined the arrangement of the repair part and completed the repair. All in all, it went well, but there was a few anxious moments when I first saw the difference between the original part and the new part.

Parts Used:

Middle Spray Arm Kit

DAVID from SAINT SIMONS ISLAND, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

SOAP DISPENSER DOOR DID NOT CLOSE.

WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.

Parts Used:

Dishwasher Detergent Lid Spring

Dishwasher Soap Dispenser Cover

Dishwasher Lid Hinge Pin

ROBERT from MAHWAH, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Part in the lower rack had rusted out

There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.

Parts Used:

Tine Row

Janet from Hollister, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

The upper rotor mount broke off.

I screwed the rack mount to the spindle using
the extra screw I ordered. I removed the upper dishrack's front stops and slid the rack
out. I clamped the mount to the dishrack. I screwed the rotor to the spindle with the screw that came with the rotor kit. I slipped the feed tube mount over the end of the tube and clamped it on the dishrack. I replaced the rack in the slides and replaced the front stops.

I had a hard time driving the screws. The slots are crossed but do not seem to be standard Phillips. The screws were hard to drive into the holes in the hard plastic. Before I could drive the mount screw all the way, the slot was too stripped to use.

Parts Used:

Dishwasher Screw

Dishwasher Upper Spray Arm Mount

Middle Spray Arm Kit

George from Wayside, NJ
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

A spring was broken in the disposal chopper

I bought the kit because it had other parts that I thought I needed.

Parts Used:

Drain and Wash Impeller Kit

Robert from Sherwood, OR
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Original lower dish rack was falling apart.

Took out old rack, put in new one. Part arrived on time and was an exact match to the original.

Parts Used:

Lower Dishrack

Chris from La Center, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Old dishrack was rusted and chipped

Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.

Parts Used:

Lower Dishrack

Donna from Hicksville, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Broken Wash Arn Retainer Nut

Screwed on a new one. The real story is getting the part. I called about noon one day and the part was dropped off at my house by FedEx the next day. Unbelievable. And the lady I talked to found the part number etc that I needed in a few minutes. Great service at a fair price.

Parts Used:

Dishwasher Wash Arm Bearing Ring

Dishwasher Wash Arm Retainer Nut

Richard from Harvard, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Dishes would'nt come clean or dry from torn boot

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Parts Used:

Rubber Washer

David from Sallisaw, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Water was leaking (gushing) out the door

Researched parts - 10 minutes - - - Ordered parts - 5 minutes - - - Waited for parts - 14 DAYS! - - - Installed parts - 5 minutes

Parts Used:

Dishwasher Wash Arm Bearing Ring

Dishwasher Pump Outlet Seal

Carla from LEWISTOWN, MT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Cap was missing/lost.

Easy fix. It’s a screw on by hand piece.

Parts Used:

Rinse Aid Cap

Jose from Coolidge, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

missing bearing ring, lower spray arm; and insufficient water supply reaching upper spray arm.

replaced those parts... but lingering doubts about adequacy of water supply due to sediment primarily from old iron pipes, evidenced in faucet aerator. So I added a Rusco hot water sediment trap filter to the supply line leading to the dishwasher and faucet, along with a new flex supply line to the dishwasher. Water supply seems improved, and any potential sediment will be caught by the trap.The time, tools, and complexity of adding the hot water sediment filter are not covered in the above.

Parts Used:

Dishwasher Wash Arm Bearing Ring

Dishwasher Upper Spray Arm Mount