110773811 Kenmore Dishwasher - Instructions

replaced spray arm, but this did not resolve the problem. The troubleshooting guid (inside kick panel) indicated the check valve may be stuck. We had quite a bit of lime build up, so I suspected the loose deposits may be stuck. I removed all of the deposits, disassembled the lower unit.
Removed lower spray arm, removed spry tube. The tube is two pieces. first the upper portion must be removed (two screws-place towel on base of tub to preven screws from falling into the chopper area), and then the lower portion simply rotates clockwise 1/8 of a turn. The attachment for lower spray arm has a small plastic bearing, careful not to drop it.
The dishwaser then had to be pulled out and turned on the side. I removed the entire lower unit by removing the white tabs (3). Careful, because the unit is now free to drop into the tub. Next I removed the pump. This is tricky as you have to remove the aluminimum bracket to get to the mountin bolt. The bolt turns out easily w/socket and extension. The pump motor is then rotated counter clockwise, and pulled from the pump. Takes a little force as the gasket makes for a tight fit.
I then removed the choper / pump unit from the basin. The build up behind the chopper screen was extensive, so I had to remove the screen and then the chopper cover. After cleaning, the check valve was unplugged and I reassembled the unit.

Dishwasher works great now.

Removed old phillips head screws /w washers from spray arm kit and mounting bracket. (You'll need to keep one screw/washer set.) Attached new mounting bracket and screwed securely. Attached spray arm with new screw/washer and I was good to go. Piece of cake!

I followed the video available on partselect.com and was easily able to follow step by step the process of removing and reinstalling a new Drain and Wash Impeller and Check Ball.

Removed the old mount from the upper rack. Removed the broken stem from the old mount that was attached to the arm. Attached the new mount to the spray arm. Attached the mount and arm to the rack.

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

Hey parts select, I'm Julia's husband and the repair was a simple remove and replace. Only one screw to hold the manifold together and the mounting hardware that we had to order separately was a snap in piece which was different form the original but went in just fine. You saved me from having to buy a new dishwasher which Julia was more than happy to go shopping for!! Thanks!!

but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door

Removed 2 screws that held the old mount and washer arm in place, new mount was very easy to install, it snapped in, only one screw needed, remounted the washer arm and the job was done. I was really impressed with the ease of ordering and how quick it got here (3 days), also the scematics you have online are very helpful. I printed them out since I don't have the owners manual any longer, they're very helpful in matching up and ordering the right part which saves a lot of time, also I like the way you can just search by model number and appliance name to find the right parts, makes the entire process really easy. I know I will continue to shop here when the need arises. It really cuts down on expensive repair costs.

removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.

Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.

Install too less that a minute. Fit perfectly.

Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much

remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.

Got the new door and tried to put it on. The door went on very easily. However, there's a spring that opens the door when the main wash cycle comes around. I never did get that spring right. None of the drawings showed the correct position and after an hour of trying to get it to work right, I gave up. The door comes open slightly (but not because of the spring) when it's time, and the liquid soap runs out due to gravity. But I wouldn't try to use soap powder because the door doesn't come open far enough.