1107693 Kenmore Dryer - Instructions

All Instructions for the 1107693
46 - 60 of 1467

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer door cable broken
37 of 46 people found this instruction helpful.
  • George from Rochester Hills, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
1. Remove the lint filter. Then remove 2 screws at the lint filter housing.

2. At the back of the dryer, remove 2 screws that restrain the hinges for the dryer top. Do NOT remove the hinges.

3. Remove the front lower access panel. It snaps at the top and hinges at the bottom. It can be slipped off the hinges. ... Read more />
4. Remove 2 screws at the bottom of the main front panel

5. The front of the dryer top is held in place by two plastic clips. Use a flat blade screwdriver (with a rag wrapped around the tip to minimize paint damage) to pry the top up at each front corner. Then tilt the top up to just past vertical. You now can see the top of the spring that is connected to the door cable.

6. Open the dryer door. Use a putty knife to pry up the plastic plug that holds the cable in place at the door. Remove the old cable from the door and insert the new one. Be sure the cable end without a hole goes into the dryer door. Replace the plastic plug.

7. Feed the new cable through the main front panel and close the door.

8. Loosen but do NOT remove two screws that hold the main front panel to each side panel. Tilt the bottom of the front panel out about 2 inches.

9. Working through the gap between the main front panel and the side, hook the spring into the hole in the cable end.

10. Working through the open top and the gap on the side, move the spring+cable up to the top. Pass the upper end of the spring through the rectangular hole in the top of the main front panel and hook the end into the small hole there.

11. Repeat for other cable as needed.

12. Reassemble all parts. You may need to hold the top of the drum up as you move the main front panel back into place. Install the main front panel lower screws before tightening the upper screws.
Was this helpful?
Thank you for voting!
Loads in the dryer took a very long time to dry often needing two full cycles to completely dry.
39 of 55 people found this instruction helpful.
  • Rod from Galveston, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First, I moved the dryer out where it would be easily accessable. I then removed the back of the dryer using a nut driver. Once this was complete, I removed the cover holding the heating element. I disconnected the two wires and puled the old element out. I replaced it with the new heating element and reconnected the two wires. I then rep lace the back cover and moved the dryer back in place. The dryer works and heats much better now. Thankyou
Was this helpful?
Thank you for voting!
Drum stopped turning, fan continued to blow
31 of 34 people found this instruction helpful.
  • Richard from Davie, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Disconnected supply. Lifted top (hinges on rear). removed two 1/4 hex head screws retaining front panel. Disconnected door switch wires. Removed front panel, lifting off from bottom tabs. Lifted out drum and discarded broken belt. Spent 30 minutes+ cleaning interior, drum skid area, dryer exit tube, motor pulley, belt tensioner, etc, e tc. Checked wiring harness for possible damage (no damage found). Repositioned drum skid pads, which had become dislodged from their intended position. Reinstalled the drum with new belt, ensuring both belt & tensioner were correctly positioned, and drum rollers and felt seals were also correctly positioned. Reinstalled front panel, tightening the two 1/4 hex head retaining screws. Reconnected power. Checked functionality. Closed top cover.
Was this helpful?
Thank you for voting!
Dryer would start and heat, but after 1st cycle the burner would not fire and a buzzing sound was coming from the gas valve solenoid area. Igniter and other functions worked fine.
32 of 38 people found this instruction helpful.
  • David from Bedford, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Removed front of dryer, unplugged each coil to determine where buzzing was coming from.....determined it was the boosting coil....ordered part and replaced. Dryer works great....we think it had be going bad over time because drying times have noticeable decreased.
Was this helpful?
Thank you for voting!
Dryer belt snapped
33 of 42 people found this instruction helpful.
  • J. from Oakdale, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
There are a total of six screws that have to be removed to do this job.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.
Was this helpful?
Thank you for voting!
dryer would not continuously heat, and took several cycles to dry clothes. The flame would ignite and heat the dryer at first, but then would ignite and go out quickly for the rest of the cycle. I tried the thermostats first with no luck.
31 of 36 people found this instruction helpful.
  • Ryan from Livonia, MI
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
I first ordered the coils from a different web site and they sent the wrong ones. The job would have been much eaiser if i had just returned and ordered from here. Instead i cut wires and tried the others but since they were worng, it did not work. I didn't label the wires so it was a puzzle to put it back together. Once i had the wir es connected properly it was a simple fix. You just open the top and take the front pannel off, remove the drum and it is right there at the bottom. Two screws take the cover off of the coils and they slide off the gas valve. Slide the new ones on and replace the cover. Put the front pannel back on, close the top and its good to go. I first tried the highlimit thermostat, and termostat with no luck. The flame would light when it was cold, but once warmed up, the flame would ignite and immediatly go out. The coils did the trick.
Was this helpful?
Thank you for voting!
Dryer door catch broke
35 of 49 people found this instruction helpful.
  • Bill from Houston, TX
  • Really Easy
  • Less than 15 mins
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this helpful?
Thank you for voting!
A high pitched squeal when drum was rolling.
28 of 30 people found this instruction helpful.
  • Robert from GOODRICH, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
First my son and I moved the dryer to the garage as we believed there would be a lot of lint possible during disassembly. Used a flat head screwdriver to pop the top from dryer housing. Then removing 2 nuts to facilitate the removal of the front of the dryer. The drum was able to be removed to diagnose the offending drum roller wheel. The drum roller wheel has experienced a failure as it had melted off of the metal spacer. Removing it and replacing with the new one was pretty easy. We then used a shop vac and an air hose to clean out all the lint, coins, paper clips and lost jewelry. Surprisingly there was not a single sock in there. Put it all back together in reverse order and plugged it in and now spins like a dream.
Was this helpful?
Thank you for voting!
My dryer only heats up at the beginning of cycle so my clothes will not dry.
31 of 39 people found this instruction helpful.
  • Monique from Mission Viejo, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I remove the front control panel and to get to the bottom front dryer door off. Using my volt meter i checked all the sensors and thermal. I surf the internet for hint and some one mention to replace the coil since some time you could have one goes out and the other working still. After i replaced the coil kit it works like a champ.
Was this helpful?
Thank you for voting!
no heat
31 of 40 people found this instruction helpful.
  • rex from streator, IL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Wrench (Adjustable)
the ignitor did not glow red checked thermal fuse by exhaust duct. fuse open replaced thermal fuse
Was this helpful?
Thank you for voting!
old lint screen -torn at wire mesh
27 of 28 people found this instruction helpful.
  • Chris from Morgan City, LA
  • Really Easy
  • Less than 15 mins
Local stores did not have any in supply. Went to Partselect and located lint screen, ordered, received in 3 days. replaced screen, Wife now happy again...
Was this helpful?
Thank you for voting!
Dryer not spinning
33 of 49 people found this instruction helpful.
  • john from goldsboro, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)
Was this helpful?
Thank you for voting!
had to replace the motor
31 of 43 people found this instruction helpful.
  • charles from parker, CO
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
Follow the advice given in the partsselect website. However, while removing the blower, my hand slipped into the housing and cut my thumb. Connected the wires to the junction box on the motor but didn't realize that the contacts would hit the drum when reinstalled. The original junction box was at a 90 degree rotation relative to the n ew box. When trying to test the breaker tripped. Using the multitester I found out that I burned out the thermal fuse, and froze the door switch. I replace both those parts and started the dryer and could hear a grinding sound. Inspection revealed that the housing of the motor was rubbing against the drum. Removing the drum yet again, I rotated the housing and replaced the drum. The dryer was finally working well.
Was this helpful?
Thank you for voting!
Dryer would dry for 5-10 minuets then no heat
35 of 55 people found this instruction helpful.
  • Richard from Jerome, MI
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
I tested the dryer coils and found that they were getting a voltage but would not open the gas valve. Coils were not bad but weak. After they warmed up they would not open the gas valve. It took 10 min to repace both coils and the heat sensor.
Was this helpful?
Thank you for voting!
The Dryer Wouldn't Heat
28 of 35 people found this instruction helpful.
  • Steve from Midwest City, OK
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First, I removed the wet clothes from the dryer. (Actually, I just kept drying them with cold air until they were dry... hee hee).
Then, I went to PartSelect.com and found a heating element for my make and model. I checked around and came back to PartSelect.com because they had the best price.

I thought about just buying t he heating coil and restringing my old one, but I'm glad I didn't because the diameters were not a match and I wouldn't have been able to restring the new larger coil through the insulator holes of my old one.

I ordered my part Sunday night online and it was stated that my part would ship to me by Monday morning. It also said to allow 3-5 days to arrive.
My part was waiting for me Tuesday when I arrived home from work. That was quick!

I took the part out of the box and looked at it and said, "Yep, that's a heating element alright. I hope it fits."

I took the heating element out to the laundry room/garage/wife's shoes and clothing storage and muscled the dryer away from the wall and into a tiny area that she calls my space.

I pulled the lint trap screen out so I could get to those two screws that keep the lint shute attached to the top and unscrewed them.

Next, I lifted the top up just like you would a car's hood. Here's a cool trick to pop the top up. Pound the upper left front with the butt of your hand at the same time you are prying the top up on the left. Do the same on the front upper right area. That should help get that top up.

There was a bracket I knew about that I had to unscrew once the top was up. The bracket holds the top ot the heating element's box. It has to be removed so you can remove the heating element's box from the back in the next step.

With that heating element box bracket removed, I closed the top back down and then put the dryer on the floor with the door down and the back facing up.

I removed all the screws that were holding the back on and put the back out of my way, but still within the confines known as my space.

I pulled two electrical wires connected to a limit switch which were attached to the heating element box. Then I pulled the two power wires from the heating element itself.

Then I wiggled the heating element box out of the dryer and unscrewed a screw that was holding the heating element to the box.

I slipped the old heating element out of the box and put it next to the new one. Then I said a couple cuss words, because I noticed that the new element was much wider than the old one.

I took the new element and tried to slip it in the box. It just barely fit. Wow, that was a close call.

I knew that the element couldn't touch any part of the box it was nested in or it would cause a short and become an electrifying experience to remember. I checked very carefully that the heating element was safely suspended inside the box and no part of coil was touching the box.

Then I reattached the box to the dryer just the way I removed it. I wired it up and the limit switch too. I put the back back on. I stood the dryer back upright and popped the top again. I reinstalled the upper heating element brace back the way it was. It was a bit of a puzzle, because it's shaped funny.

Then I closed the top back down and it snapped into place. I put the lint trap screws back in. I positioned the dryer back were it likes to dance best and plugged it in.

I turned it on and it got hot. End of story!
Was this helpful?
Thank you for voting!
All Instructions for the 1107693
46 - 60 of 1467