1107690 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The belt you sent was too short
6 of 7 people
found this instruction helpful.
-
Larry from Middlebury, IN
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I disassembled the dryer, replaced the pulley (which was noisy), and the belt.reassembled, only to find out that the drum would not turn freely. checked all my procedures and kept having the same problem. Finally after 3 frustrating hours, I took the back off and noticed that idler arm was tight against the motor shaft, because the too s
... Read more
hort belt didn't allow for the clearance needed. Had too take everything apart ,another hour, went and found one at our local repair shop, reinstalled everything , after another two hours runs fine. would appreciate a refund. And please check your part numbers in the future. Would hate to have someone else go through what i experienced.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken Motor Pulley
7 of 10 people
found this instruction helpful.
-
Mark from PELHAM, MA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Socket set
Removed back panel of the dryer-reached my hand to the back of the motor shaft, put 7/16 wrench on it to hold the shaft while I removed the broken pulley with pliers. Very easy fix-the tech on Utube took the entire dryer apart totally unnecessary. If that is what the factory tells its tech"s to do its no wonder why the labor charge woul
... Read more
d be thru the roof.
Read less
Was this helpful?
Thank you for voting!
Dryer got hot then heat would shut off
6 of 7 people
found this instruction helpful.
-
Douglas from Fernley, NV
- Really Easy
- 30 - 60 mins
-
Nutdriver, Socket set
Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and r
... Read more
everse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.
Read less
Was this helpful?
Thank you for voting!
Drive pulley broke. Looked like clip holding it on broke and pulley was running crooked.Belt was squealing some a couple of weeks before it broke.
6 of 7 people
found this instruction helpful.
-
Mark from Sheffield, PA
- Easy
- 30 - 60 mins
-
Socket set
Removed top and back covers. Placed new pulley and retaining clip in place. I had to remove a couple of drum supports to put belt on. Probably didn't have to remove top.
Other Parts Used:
Was this helpful?
Thank you for voting!
Old lint filter was broken
8 of 14 people
found this instruction helpful.
-
Earl from Santa Ana, CA
- Really Easy
- Less than 15 mins
Just replaced the old lint filter.
Was this helpful?
Thank you for voting!
Dryer had no heat at all. This is an older gas dryer.
5 of 5 people
found this instruction helpful.
-
todd from MILFORD, PA
- Really Easy
- Less than 15 mins
-
Wrench set
Cleaned out years of fuzz behind lower access panel and noticed where the igniter sits there is a metal tube about 1 inch in diameter. It had rust on the end and was starting to flake away. Found some helpful hints about how to test the igniter. Very easy, just used an ohmeter. Unplugged the 2 pin wire connector and checked for continuit
... Read more
y. 1 lead on 1 pin and the other on the other pin., igniter side not the harness side from the dryer. A good igniter should read less than 5 ohms. I don't know the spec. exacttly, but it should not read open or infinite resistance. My meter read an open circuit. Removed the tube and igniter assembly, mine only 2 small bolts. I found the igniter element cracked. Ordered and installed igniter and tube assembly. This was a very easy install. 20 year old dryer works great and it's better than spending $500.00+ on a new one.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Lint filter seal worn out
5 of 5 people
found this instruction helpful.
-
Dennis from PALM BCH GDNS, FL
- Very Easy
- Less than 15 mins
The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.
Was this helpful?
Thank you for voting!
No heat, would not light because igniter burnt out
6 of 8 people
found this instruction helpful.
-
anthony from Port Arthur, TX
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two scr
... Read more
ews. Plug in dryer and there you go drying clothes again. Wife all happy again.
Read less
Was this helpful?
Thank you for voting!
Noisy
5 of 5 people
found this instruction helpful.
-
Robert from HAGERSTOWN, MD
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Disconnect power supply, remove power cord from dryer, remove dryer vent tube from dryer, remove 2 Philips screws from power connection on dryer, remove nuts from back of dryer, remove back of dryer. Locate idler pulley at bottom of unit at the rear of the motor, pull pulley back to loosen belt and remove from pulley, remove pulley retain
... Read more
er clip, remove pulley and rear washer from shaft and inspect shaft for wear or rust. replace washer and pulley (no specific direction to replace them, washer first then pulley). Reverse above procedure to reassemble. This is for a front load dryer, a top load dryer is different.
Read less
Was this helpful?
Thank you for voting!
Dryer was Noisy
6 of 8 people
found this instruction helpful.
-
Doug from HARRODSBURG, KY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I simply followed the video and apart from a couple of areas that were not relevant to my model, everything went exactly as illustrated. The video is excellent and made the repair so easy.
The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back ... Read more and two in the front.
A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.
It was an easy fix, I just did half the install a second time.
The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back ... Read more and two in the front.
A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.
It was an easy fix, I just did half the install a second time.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would only heat at start up for one cycle
6 of 8 people
found this instruction helpful.
-
Rob from Henderson, NV
- Really Easy
- 30 - 60 mins
-
Nutdriver
Ohmed coils and both had continuity so I changed radiant heat sensor. No bench test for Radiant Heat sensor. Same problem. Changed both coils and dryer works fine. Weak coils were my problem. I read thru the same issues in Parts Select forum and it said Radiant Heat sensor was problem 25% of the time. With coils having continuity and no o
... Read more
hm value specified for coils I made wrong choice but, I have spare parts and look for another 10 years of life in the dryer. Nice to have this forum to research appliance repair. Very helpful for parts location and installation. Dishwasher is next!
Read less
Was this helpful?
Thank you for voting!
The landry would not dry all the way at the end of the cycle.
8 of 14 people
found this instruction helpful.
-
Mark from Houston, TX
- Easy
- 30 - 60 mins
First i removed the rear panel on the dryer.the removed bothe thermostats that were on the blower housings.unpluged all wiers and installed new thermostats.reinstalled the wiers in there proper locations...note to log the location of the wires when removing from old switch.reinstalled the rear panel and hooked dryer back up and test.
Other Parts Used:
Was this helpful?
Thank you for voting!
not drying all the way, not getting hot enough
6 of 8 people
found this instruction helpful.
-
robert from cedar lake, AL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
loosened two screws on back of top,lifted top away from front panel.it just lifts off front corners,removed two screws at top corners.lift front panel up and out,this panel supports dryer tub,remove slowly,unplug door switch parts are located left side bottom two screws holding in had to have wife hold drum up to put front panel on
Other Parts Used:
Was this helpful?
Thank you for voting!
Drum support roller making very loud noise
5 of 5 people
found this instruction helpful.
-
William from TROY, AL
- Really Easy
- 1- 2 hours
-
Screw drivers, Socket set
had to take front off of Dryer then was able to replace drum roller
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would not heat up properly. It would heat initially but once the heat was off it would not come on again.
5 of 6 people
found this instruction helpful.
-
Joseph from Chicago, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I followed the advice posted by other customers. I took the front off the dryer, put the door back in place and ran a cycle. I could see that the igniter was heating properly, but no gas was flowing. Based on what I read I concluded that it was a problem with one of the gas valve coils. It was relatively inexpensive to replace both (a
... Read more
nd the dry is 10 years old), so I didn't go to the trouble of determining the bad one. I replaced them both. Obviously I unplugged the dryer (no need to turn off gas). There were 2 screws that held the bracket in place which holds the coils. I disconnected the coils, removed the bracket screws, replaced the coils, reattached the bracket screws and reconnected the coils. I then reattached the front plate to the dryer. It was very easy and took about 20 minutes and I had never worked on a dryer before.
Read less
Was this helpful?
Thank you for voting!