1107657 Kenmore Dryer - Instructions

All Instructions for the 1107657
121 - 135 of 927

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer motor quit working
3 of 3 people found this instruction helpful.
  • Tommy from BRUSH, CO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
i took the face off dryer and removed the belt and drum then removed the lint trap from back to clean and have access fan then removed the retaing clips holding the motor then with two adjustable wenches unscewed the motor from fan took out motor and replaced in reverse order all you needed was some common sence to do this i though it was easy to do greats parts fit perfect thanks tommy
Was this helpful?
Thank you for voting!
the dryer would not turn on
4 of 6 people found this instruction helpful.
  • Warren from PHILADELPHIA, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
The first step was to check the electrical supply to make sure I had power 120 volt. I unplugged the dryer and turned off the gas supply and turned the dryer around so I could have access to the back panel removed panel to access the wiring harness and safety thermostats. All switches and wire checked good with my ohmmeter .I pulled off t he front kick panel and checked the electrical schematic and found the door switch was in the circuit to check it I had to lift up the top and pop out the front to access the door switch checked switch and found it defective. Replaced switch vacuumed out dryer and vent reassembled dryer and all worked good.
Was this helpful?
Thank you for voting!
broken blower wheel
3 of 3 people found this instruction helpful.
  • Vern from NEWBERG, OR
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.
Was this helpful?
Thank you for voting!
Mother was frozen up
3 of 3 people found this instruction helpful.
  • Dan from SYRACUSE, UT
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
I followed the video. So easy..
Was this helpful?
Thank you for voting!
Rear drum rollers were shot.
3 of 3 people found this instruction helpful.
  • David from JOLIET, IL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.
Was this helpful?
Thank you for voting!
Needed a new lint filter
3 of 3 people found this instruction helpful.
  • Evelyn from JACKSONVILLE, FL
  • Very Easy
  • Less than 15 mins
Took the old one out, replaced it with new one.
Was this helpful?
Thank you for voting!
Start and then kick out.
5 of 9 people found this instruction helpful.
  • PHILLIP from AUSTIN, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Was this helpful?
Thank you for voting!
Dryer would not run
4 of 6 people found this instruction helpful.
  • james from york, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
Was this helpful?
Thank you for voting!
Lint Filter wore out.
4 of 6 people found this instruction helpful.
  • Claude from Austin, TX
  • Really Easy
  • Less than 15 mins
It required no tools, just take out the old torn filter and slip in the new one. I should have ordered it a year ago, with the ease of the website and the delivery via Fed Ex. super easy.
Was this helpful?
Thank you for voting!
Dryer drum wouldn't turn and motor would shut off
3 of 4 people found this instruction helpful.
  • Cynthia M from Westfield, MA
  • Easy
  • More than 2 hours
  • Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Was this helpful?
Thank you for voting!
Dryer making a screeching noise. Diagnosed by removing idler pulley first, then turning the motor and learning that it was the motor that was squeaking or the blower fan.
3 of 4 people found this instruction helpful.
  • Linda from GIBSONIA, PA
  • Easy
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Ordered the motor with pulley and blower wheel in case the wheel did not come free from the motor.
Took out the lint screen, took off the top and disconnected the wires for the door switch, took off the front.
Remove the idler poi and the belt and then removed the drum.
I read in other repair YouTube videos, the blow er wheel sometimes is so seized onto the motor axle that you have to remove the wheel by cutting it off.
Yes, ours seized!
Cut off the motor axle with a hacksaw and then the motor and the wheel were free. This was not an issue since I had purchased both the motor and the wheel which I recommend doing anyway. Our dryer over 25 years old and it does not have many electrical components, which I love. We removed the parts put in the new parts. Follow the wiring diagram to get the new motor hooked up.
Then I replaced the drum support rollers, which were a snap and then we put it all back together.
We added an extra step because we had to takeoff the back of the dryer to gain access to the blower. It turned out to be a good thing since years of lint have been trapped at the bottom of the lint chute.
I cleaned everything, washed everything and put it all back together and it purrs like a kitten.
Took us about 2 1/2 hours total since we are very cautious and slow as we didn’t want to break things.
I am very happy with the end result and hopefully it will last another 25 years!
Parts were spot on and worked perfectly.
Much more economical than buying a new dryer for $750-$1000.
Was this helpful?
Thank you for voting!
Motor failure
3 of 4 people found this instruction helpful.
  • Sam from MINNEAPOLIS, MN
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Followed the video instructions to replace motor, belt, and rollers (belt and rollers looked to be in ok shape, but as long as I had the thing open I figured I might as well). Fairly straightforward procedure. Trickiest parts were getting the rear roller clips in place and re-attaching the rear motor spring clip. Probably could've found a used dryer of comparable quality for less, but this was easier and more satisfying than moving dryers in and out of the basement.
Was this helpful?
Thank you for voting!
Dryer heating up but clothes not drying
3 of 4 people found this instruction helpful.
  • Donald from Knoxville, TN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Removed back and then removed lint slide.
Vacuumed all of the cabinet and and washed lint chute.
Blower seal and lint seals were crumbling since dryer is 24
years old. Part Select diagrams and repair videos are extremely helpful in showing the process. Dryer now working like new.
Was this helpful?
Thank you for voting!
Clothes were being marked up due to bad rear drum seal.
3 of 4 people found this instruction helpful.
  • Kevin from Charlotte, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Unplug Cord of course.

I removed 2 screws holding the lint trap housing in place and pulled the top forward and up. I then lifted the front panel up and wiggled it a little and it came free and I put it aside. I got on the floor and removed the belt from the motor by lifting the tension pulley releasing the tension and pulling the belt sideways. The drum easily lifted out at this point and I placed it on some newspaper and towels I had placed on the floor in advance.

I then peeled of all the belt that would come off at this point and then took some paper towels and wet them with acetone and worked just few inches at a time so the acetone would not evaporate before I got the glue off. This went much quicker and easier than I dared hope. From there it was just a matter of applying an even bead of glue all around and quickly starting in one spot and putting on the new belt making sure it was all the way back and pulling it tight as it is only just long enough so you don't want to get to the end and wind up short and your glue already set.

I then gathered my $2.37 tip from the bottom of the dryer and vacuumed the lint that was there while I let the glue set some more.

Putting the drum back on was a tad tricky but not bad. Just concentrate on getting it between the idler wheels and the hub first. Make sure the lower wheel is pulled forward. I Used a small box and some cardboard to hold the drum at the right height while I put the belt back on although if you have some extra hands available now would be a good time to get them. Then having put the front panel within reach I pulled out the box and replaced the panel, lowered the top and replaced the screws, spun it by hand then tried it with power. All is good. Time about 45 min.
Was this helpful?
Thank you for voting!
Broken Drum Roller Support
3 of 4 people found this instruction helpful.
  • Lawrence from Cedar Grove, NJ
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
After reading about repairs to the drum rollers, it was suggested to change the rear drum seal at the same time. The drum rollers were very easy to change and took no time at all. The rear seal was a different story. The instructions in the packet could have been more explicit. The seal has to be streched around the drum at first. Then an d only then can you install the seal on the drum edge. You should also have several clamps available to hold the seal in place as you glue the outside flap. Leave the clamps in place until the glue dries, then re-install the drum.
Was this helpful?
Thank you for voting!
All Instructions for the 1107657
121 - 135 of 927