11076409 Kenmore Dryer - Instructions

All Instructions for the 11076409
121 - 135 of 1249

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Two cycles to dry clothes
4 of 4 people found this instruction helpful.
  • Alan from Lebanon, OH
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplug the dryer and remove the back panel. I lifted the top of the dryer for easy access to the screw that held the Heater Box. Removed the Heater box, unbolted the heating element, pulled the old one out put the new one in the reversed the process.

I ordered the part Saturday, had it by Tuesday.
Was this helpful?
Thank you for voting!
drum roller became lose and seperated from the shaft that supports it. it had to be replaced
5 of 7 people found this instruction helpful.
  • Dillard C. from Vina, AL
  • Easy
  • 15 - 30 mins
  • Socket set
remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse
Was this helpful?
Thank you for voting!
Broken drive belt
7 of 13 people found this instruction helpful.
  • Stanley from Flushing, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.
Was this helpful?
Thank you for voting!
dryer would not turn on
5 of 7 people found this instruction helpful.
  • Larry from Bethpage, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Found the switch part on the floor and after I figured out where it came from it was minutes before it took to find the web site and order the part, I then watched the installation video which helped with a few pointers and days later it was installed and fixed for 10 dollars with shipping,AMAZING!!!
Was this helpful?
Thank you for voting!
Heating element was toast
4 of 4 people found this instruction helpful.
  • Jesse from CHURCH POINT, LA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Undid the back, remove wires going to element, unscrew lint trap, pop the top and undid the nut-screw holding the element housing. pulled out the bad element and did everything in reverse with the new element... unplug it first though because I left that step out.
Was this helpful?
Thank you for voting!
For the thermal fuse, dryer would not start. For the heating element, dryer would not heat up.
4 of 4 people found this instruction helpful.
  • Robert from Winfield, AL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
First disconnect power supply either by switching off breaker or unplug dryer cord, or do both if you are a safety freak. Pull dryer out so you can get to the back panel. Take the dryer hose off, then take screws out from around panel and remove it. For the THERMAL FUSE take one screw out, unplug wires and replace thermal fuse. For HEATIN G ELEMENT, unplug the two wires from element. At top of air duct there is one screw to get out. You need a long flat head screwdriver. Reach through a small hole on dryer back to the screw. Once screw is out, lift up on air duct to get it out. Once you have it out there is one screw holding heating element in air duct. Remove screw, slide element out and reverse steps from when you took it apart to put it back together.
Was this helpful?
Thank you for voting!
My dryer stopped heating
5 of 7 people found this instruction helpful.
  • Jennifer from CLINTON, MS
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
The repair was really easy and I loved the DIY videos they were great, not many tools needed to do these repairs that was great. The only thing is this didn't solve my issue.
Was this helpful?
Thank you for voting!
No Gas Heat
4 of 5 people found this instruction helpful.
  • Debra from Springfield, PA
  • Very Difficult
  • More than 2 hours
  • Nutdriver
I did what any novice would have done. I took the entire thing apart to get to the gas jet. I did not know about the thermal fuse until I got to the schematic behind the timer and controls. I was a tech back in the 70's and 80's and only worked on electric dryers. Back then I would remove the heater core and twist the coils together t o save money. So I had no idea how a gas dryer heating unit worked. So now any one that reads this. You do not have to take the dryer completely apart, I did that for all of you. Just replace the thermal fuse on the back of the unit by unplugging that wires and removing the screws! It looks like a long white piece of plastic with 2 wires to it. You will find this under the full metal shield on the back of the unit. This should be about a 1 hour repair at the most!
Was this helpful?
Thank you for voting!
Whirlpool Gas dryer, run but no heat
4 of 5 people found this instruction helpful.
  • Fred from Macomb, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I simply removed the rear panal of the dryer. Removed the two wires from the fuse at the rear of the dryer. Attached an OEM meter across the two fuse connections and had no continuity. Ordered a new fuse and recieved it in 2.5 days.Replaced the fuse,reconnected the wires and replaced the rear panal. Started dryer and it now blows hot air and runs like new. I can't say enough about PartSelect. Great diagnosis using their website, the delivery was fast and I recieved the correct part at a good price. Very satisfied, Thanks PartSelect. Fred F
Was this helpful?
Thank you for voting!
Dryer makes squealing noise, finally the motor seized up.
4 of 5 people found this instruction helpful.
  • Anthony from PITTSTON, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.
Was this helpful?
Thank you for voting!
Frig stopped cooling - Freezer side iced up
6 of 11 people found this instruction helpful.
  • Walter R from Gainesville, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
After un-plugging the frig and allowing it to defrost, we emptied the frig and gave it a thorough cleaning inside and outside. I then removed the shelving in the freezer and the face plate at the back of the machine. One of the defrost heater coils had burned out and there was a loss of continuity which was keeping the frig from defrost ing properly. The old heater snapped out easily. I went to this website and ordered a new defrost heater assembly which arrived practically overnight. It was identical to the old one and installed as quickly and easily as the original had come out. I put the faceplate back on, put the shelving back in, placed a thermometer inside the fresh food section, plugged it in and waited until I heard ice cubes drop. The fresh food section was holding at 41 degrees F which is optimum. The refrigerator has been working smoothly every since! Easy job!
Was this helpful?
Thank you for voting!
Heating unit burned out.
4 of 5 people found this instruction helpful.
  • Charles from Osceola, MO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Followed the instructions, removed the back cover, disconnected the top, disconnected the element and removed the element holder, then the element. Reversed procedure to install the new part.
Was this helpful?
Thank you for voting!
a loud, high-pitched ringing noise
4 of 5 people found this instruction helpful.
  • Craig from Booneville, AR
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Raised the top of the dryer then took the front of the dryer off. Took the drum off. Replaced the pulley and support rollers. Then, put the new belt on and put it back together.
Was this helpful?
Thank you for voting!
Drier ran but would not heat up.
4 of 5 people found this instruction helpful.
  • Robert from Arnold, MD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
removed 5 screws holding back cover on. Oh yeah very important (that is if you'd like to be around to help your buddy do this) unplug the unit 1st!
Accessed the heat coil. Difficult to remove the element so opened top of dryer to access the screw that was on top of the housing was then able to easily remove the element and replace wi th the new one. Actually, removing the top of the drier was a very good thing because it gave me a chance to throughly clean out any lint. but number one reason was I found the drier door cutoff switch wire had come loose from its clip and was laying on top of the drum and slowly grinding the insulation off the wire! had not shorted yet but would have failed soon.
anyway... I got cheap when buying the parts and didn't buy the real part that was bad... (lesson learned) anyway found the parts I did replace were not bad. So back to the net again to order the last thermal limit switch and fuse. received the parts 3 days later installed them. Now life is good! Well at least dry warm shirts and socks! Decide to keep the extra parts just in case I need them down the line.
Actually even with the problems encountered "I" still repaired the drier myself saving big bucks and enjoyed the small but fulfilling challenge!
Excellent experience working through partselect.com
Was this helpful?
Thank you for voting!
Clothes took multiple cycles to fully dry.
4 of 5 people found this instruction helpful.
  • Donald from Pine City, NY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Removed rear panel, removed 3 screws and old element and installed new element. To install new element I only needed one screw and spliced in the two wires that were provided with the element. This repair was simple and now the dryer works great.
Was this helpful?
Thank you for voting!
All Instructions for the 11076409
121 - 135 of 1249