11076404 Kenmore Dryer - Instructions

All Instructions for the 11076404
121 - 135 of 914

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer motor quit working
3 of 3 people found this instruction helpful.
  • Tommy from BRUSH, CO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
i took the face off dryer and removed the belt and drum then removed the lint trap from back to clean and have access fan then removed the retaing clips holding the motor then with two adjustable wenches unscewed the motor from fan took out motor and replaced in reverse order all you needed was some common sence to do this i though it was easy to do greats parts fit perfect thanks tommy
Was this helpful?
Thank you for voting!
the dryer would not turn on
4 of 6 people found this instruction helpful.
  • Warren from PHILADELPHIA, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
The first step was to check the electrical supply to make sure I had power 120 volt. I unplugged the dryer and turned off the gas supply and turned the dryer around so I could have access to the back panel removed panel to access the wiring harness and safety thermostats. All switches and wire checked good with my ohmmeter .I pulled off t he front kick panel and checked the electrical schematic and found the door switch was in the circuit to check it I had to lift up the top and pop out the front to access the door switch checked switch and found it defective. Replaced switch vacuumed out dryer and vent reassembled dryer and all worked good.
Was this helpful?
Thank you for voting!
Dryer would not start, showed F40 code
3 of 3 people found this instruction helpful.
  • Glenn from KINGSPORT, TN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Very easy do it yourself repair, and saved at least $300.00. I watched a video and it took me less than 20 minutes to complete repair. Part fit perfect and I have already ordered another to keep as a spare.
Was this helpful?
Thank you for voting!
Mother was frozen up
3 of 3 people found this instruction helpful.
  • Dan from SYRACUSE, UT
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
I followed the video. So easy..
Was this helpful?
Thank you for voting!
The drum made a lot of noise while turning. The dryer shook
3 of 3 people found this instruction helpful.
  • Craig from VASS, NC
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
Was this helpful?
Thank you for voting!
There dryer was not producing any heat
3 of 3 people found this instruction helpful.
  • Terry from Boise, ID
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
I unplugged the dryer from the electrical outlet, removed the back of the unit and checked the heating element for continuity. There was no reading. I then removed the housing and heating element and visually inspected it. The coiled wire was broken in two places.
I then did a Google search with the model number and found Parts Selec t. I placed my order Sunday afternoon and the part arrived the following Wednesday. That evening it took about 20 minutes to install the new element,put the back on the dryer and re-attach the exhaust tube.
The old dryer is as good as new again.
TJ in Boise
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people found this instruction helpful.
  • Raymond from Washington, DC
  • Really Easy
  • Less than 15 mins
  • Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people found this instruction helpful.
  • WILFRED from NORTH HIGHLANDS, CA
  • Really Easy
  • Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
Dryer door actuator lever broke
3 of 4 people found this instruction helpful.
  • Mark from Clarksburg, MD
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. R einstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.
Was this helpful?
Thank you for voting!
door switch lever/latch broke
3 of 4 people found this instruction helpful.
  • Ed from Charlottesville, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating elemen t, and other parts. At some point it will be time for a new dryer...
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 4 people found this instruction helpful.
  • Wayne from Rosenberg, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.
Was this helpful?
Thank you for voting!
Broken belt
3 of 4 people found this instruction helpful.
  • peter from portland, OR
  • Easy
  • 15 - 30 mins
  • Nutdriver
Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt fro m potentially slipping off the driveshaft.
Was this helpful?
Thank you for voting!
The sound was like a cement mixer
3 of 4 people found this instruction helpful.
  • Russell from Apache Junction, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked u p the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.
Was this helpful?
Thank you for voting!
Dryer was not drying the clothes but running like normal
3 of 4 people found this instruction helpful.
  • Kevin from Belmont, NC
  • Easy
  • 15 - 30 mins
  • Nutdriver
I realized from this issue years ago that it was porbably the heating element. I took the dryer to the garage and remove the back and figured out how to get the heating element out. Once I had it out it had a break in the coil so I knew I needed that part. I hit parts select on line and ordered the part. I left everything in the garage an d waited for the part. In a couple of days it came and I put it in and took the dryer back to the laundy knook, gave it a test run and Its all good!
Was this helpful?
Thank you for voting!
the lower drum support roller had been chewed to bits.
3 of 4 people found this instruction helpful.
  • Rodney from Mt. Jackson, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.
Was this helpful?
Thank you for voting!
All Instructions for the 11076404
121 - 135 of 914