11076402 Kenmore Dryer - Instructions

All Instructions for the 11076402
106 - 120 of 897

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken drum belt
4 of 4 people found this instruction helpful.
  • Michelle from Fort Myers BEach, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, t he belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.
Was this helpful?
Thank you for voting!
Broken drive belt
7 of 13 people found this instruction helpful.
  • Stanley from Flushing, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.
Was this helpful?
Thank you for voting!
dryer would not turn on
5 of 7 people found this instruction helpful.
  • Larry from Bethpage, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Found the switch part on the floor and after I figured out where it came from it was minutes before it took to find the web site and order the part, I then watched the installation video which helped with a few pointers and days later it was installed and fixed for 10 dollars with shipping,AMAZING!!!
Was this helpful?
Thank you for voting!
Dryer makes squealing noise, finally the motor seized up.
4 of 5 people found this instruction helpful.
  • Anthony from PITTSTON, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.
Was this helpful?
Thank you for voting!
Frig stopped cooling - Freezer side iced up
6 of 11 people found this instruction helpful.
  • Walter R from Gainesville, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
After un-plugging the frig and allowing it to defrost, we emptied the frig and gave it a thorough cleaning inside and outside. I then removed the shelving in the freezer and the face plate at the back of the machine. One of the defrost heater coils had burned out and there was a loss of continuity which was keeping the frig from defrost ing properly. The old heater snapped out easily. I went to this website and ordered a new defrost heater assembly which arrived practically overnight. It was identical to the old one and installed as quickly and easily as the original had come out. I put the faceplate back on, put the shelving back in, placed a thermometer inside the fresh food section, plugged it in and waited until I heard ice cubes drop. The fresh food section was holding at 41 degrees F which is optimum. The refrigerator has been working smoothly every since! Easy job!
Was this helpful?
Thank you for voting!
Clothes took multiple cycles to fully dry.
4 of 5 people found this instruction helpful.
  • Donald from Pine City, NY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Removed rear panel, removed 3 screws and old element and installed new element. To install new element I only needed one screw and spliced in the two wires that were provided with the element. This repair was simple and now the dryer works great.
Was this helpful?
Thank you for voting!
a loud, high-pitched ringing noise
4 of 5 people found this instruction helpful.
  • Craig from Booneville, AR
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Raised the top of the dryer then took the front of the dryer off. Took the drum off. Replaced the pulley and support rollers. Then, put the new belt on and put it back together.
Was this helpful?
Thank you for voting!
Heating unit burned out.
4 of 5 people found this instruction helpful.
  • Charles from Osceola, MO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Followed the instructions, removed the back cover, disconnected the top, disconnected the element and removed the element holder, then the element. Reversed procedure to install the new part.
Was this helpful?
Thank you for voting!
There dryer was not producing any heat
3 of 3 people found this instruction helpful.
  • Terry from Boise, ID
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
I unplugged the dryer from the electrical outlet, removed the back of the unit and checked the heating element for continuity. There was no reading. I then removed the housing and heating element and visually inspected it. The coiled wire was broken in two places.
I then did a Google search with the model number and found Parts Selec t. I placed my order Sunday afternoon and the part arrived the following Wednesday. That evening it took about 20 minutes to install the new element,put the back on the dryer and re-attach the exhaust tube.
The old dryer is as good as new again.
TJ in Boise
Was this helpful?
Thank you for voting!
broken blower wheel
3 of 3 people found this instruction helpful.
  • Vern from NEWBERG, OR
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.
Was this helpful?
Thank you for voting!
dryer motor quit working
3 of 3 people found this instruction helpful.
  • Tommy from BRUSH, CO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
i took the face off dryer and removed the belt and drum then removed the lint trap from back to clean and have access fan then removed the retaing clips holding the motor then with two adjustable wenches unscewed the motor from fan took out motor and replaced in reverse order all you needed was some common sence to do this i though it was easy to do greats parts fit perfect thanks tommy
Was this helpful?
Thank you for voting!
Mother was frozen up
3 of 3 people found this instruction helpful.
  • Dan from SYRACUSE, UT
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
I followed the video. So easy..
Was this helpful?
Thank you for voting!
Rear drum rollers were shot.
3 of 3 people found this instruction helpful.
  • David from JOLIET, IL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.
Was this helpful?
Thank you for voting!
Let the kids do it.
3 of 3 people found this instruction helpful.
  • Robert from Rocky Mount, NC
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gav e my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis
Was this helpful?
Thank you for voting!
Dryer Drum Belt Broken
3 of 3 people found this instruction helpful.
  • george s from las vegas, NV
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made m ore in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.
Was this helpful?
Thank you for voting!
All Instructions for the 11076402
106 - 120 of 897