110749 Kenmore Dryer - Instructions

Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor.
Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in h ... Read more andy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.

checked to see what the problem might be according to your website, ordered the recommended parts, received parts within 3 business days, watched video on website with instructions, replaced parts and surprise, dryer works as if nothing ever happened. thank you for the straightforward, no nonsense information and video provided in your we ... Read more bsite and the promt efficient service

1) Removed top of dryer
2) removed belt and drum
3) removed front of dryer
4) popped clips holding down motor
5) unscrewed rear fan from motor (by exposing and holding fan)
6) changed motor
7) changed support rollers and idler pully
8) reassemled dryer

I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with th ... Read more e new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.

Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem ... Read more was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.

Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine....

With the correct parts and watching the video, it was so easy to repair. We ordered the wrong part (for the Electric Dryer when it should have been for the Residential Dryer) but the return was easy and we got the new parts super fast. Next time I would probably look at the offending part first before ordering just to make certain. But w ... Read more e used a socket set and Philips screwdriver and actually had our teens do all the work for experience. Fixed the loud noise one and for all.

I used a multi meter to find coils failed in warmed temperature condition.
I tested main switch for different cycle operation. Main switch was worn out inside and not making good contact for soft cycles.
This dryer is 25 years old. I chose to replace all the sensors, fuses, ignitor, gas valve coils, cycle switch and thermostat. ... Read more
This was cost effective for me, because now, I actually have a good dryer that might just last another 25 years. I might replace the drive belt soon. I'll order from Parts Select. This was easy and fun. Thanks!

First, I watched a utube video of replacing the dryer belt. Then I went to Sears Hardware and couldn't find a part. Then I ordered the parts for my favorite online repair parts source - partselect.com. I had the part in one day! We did exactly what the video showed and also replaced the two wheels that looked like roller blade wheels. Pie ... Read more ce of cake. Saved a $75 repair call plus whatever the parts would have been and spent about 20 minutes doing it. Back in business. Great for a 12 year old dryer! Buy the dryer kit!

After unplugging and removing the back cover from the dryer, locate the push button switch. Slide putty knife around outer cover to unhook catch. Replace with new push button switch. My dryer is still not working, but this was a simple replacement.

once the back is off remove belt from tentioner and remove v clip. smooth shaft with wd-40 and scotch brite , then install new idler replace v clip
and your done !!!

Removed back cover, removed broken switch, replaced with new switch, replaced back cover, told wife her dryer was fixed.

I moved the dryer to a location where I could get to both the front and back sides. I opened the back by first removing the top cover and then the back. It requires either a Phillips head screwdriver or a quarter inch socket. In addition, it requires removing the four power wires which connect to the computer. If you are unfamiliar with t ... Read more he wiring layout, take a photo with your cell phone which you can then refer to when re-assembling. Once the back was removed, I saw that the belt was still intact, but the pulley which provides tension to the belt was frozen. Take a photo of the belt route between the motor and the pulley. Try to get the spring position in the photo. Remove the belt from the pulley by reducing the tension and then sliding the belt out (this assumes the belt is not broken). The pulley arm is held in place by a single bolt which can be removed by a socket set. Remove the arm with the pulley attached. Examine the pulley to figure out why it is frozen. In my case, the pulley had been frozen for some time and the belt had actually chewed through the pulley and was sliding (polishing) on the pulley axle? I used a pair of pliers to loosen the destroyed pulley by rotating it back and forth over the axle while gripping the arm the axle is attached to. As it loosened up I worked it off the axle. I used a cloth to clean the axle of grime from the belt, pulley, and dryer lint. The new pulley comes with a washer and triangular plastic "fastener". First you put on the washer, then the pulley and then you secure it on the axle by sliding the triangular fastener over the axle so it sits in a small grove near the end of the axle. Then put the pulley arm back by replacing the bolt. Make sure you do not overtighten the arm since it is intended to rotate about the bolt. If the dryer belt breaks, the spring will pull the arm down and throw a cutoff switch. Its operation should be obvious. Once the arm is back in place, refer to your photo and replace the spring (this can be tricky and frustrating, particularly if you don't use something like needle nose pliers). Once the spring is in place, depress it and re-install the dryer belt. Refer to the photo you took earlier if you've forgotten how the belt was routed. Then re-install the dryer's back panel, re-attach the electric wires (again refer to the photo you took earlier), and re-attach the top cover. You might want to test your handiwork at this point before you reconnect the dryer vent

I looked for squeaky dryer within parts select and went with the 80%. I received the Maintenance Kit, replaced two rollers and it works like new. Amazing since this is the first time I have ever opened a dryer. The instruction sheet and parts were all I needed.

Took the old filter out and inserted the new one- works great!!