110746 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer would start and heat, but after 1st cycle the burner would not fire and a buzzing sound was coming from the gas valve solenoid area. Igniter and other functions worked fine.
32 of 38 people
found this instruction helpful.
-
David from Bedford, IN
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Removed front of dryer, unplugged each coil to determine where buzzing was coming from.....determined it was the boosting coil....ordered part and replaced. Dryer works great....we think it had be going bad over time because drying times have noticeable decreased.
Was this helpful?
Thank you for voting!
dryer would not continuously heat, and took several cycles to dry clothes. The flame would ignite and heat the dryer at first, but then would ignite and go out quickly for the rest of the cycle. I tried the thermostats first with no luck.
31 of 36 people
found this instruction helpful.
-
Ryan from Livonia, MI
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I first ordered the coils from a different web site and they sent the wrong ones. The job would have been much eaiser if i had just returned and ordered from here. Instead i cut wires and tried the others but since they were worng, it did not work. I didn't label the wires so it was a puzzle to put it back together. Once i had the wir
... Read more
es connected properly it was a simple fix. You just open the top and take the front pannel off, remove the drum and it is right there at the bottom. Two screws take the cover off of the coils and they slide off the gas valve. Slide the new ones on and replace the cover. Put the front pannel back on, close the top and its good to go. I first tried the highlimit thermostat, and termostat with no luck. The flame would light when it was cold, but once warmed up, the flame would ignite and immediatly go out. The coils did the trick.
Read less
Was this helpful?
Thank you for voting!
Dryer belt snapped
33 of 42 people
found this instruction helpful.
-
J. from Oakdale, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
There are a total of six screws that have to be removed to do this job.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the ... Read more dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the ... Read more dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.
Read less
Was this helpful?
Thank you for voting!
push to start switch was not working
33 of 43 people
found this instruction helpful.
-
Grace from New Smyrna Beach, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Removed the old one and installed the new one! What impressed me the most was the amount of time for delivery, one day! Actually it came before 24 hrs!!! Very impressive! I would highly recommend this company!!!
Was this helpful?
Thank you for voting!
Top door catch assembly had broken
29 of 31 people
found this instruction helpful.
-
tony from prineville, OR
- Easy
- Less than 15 mins
-
Screw drivers
It was so easy, that my wife did it the day we got the part before I got home from work. She wedged it out with a flat head screw driver and then pushed the new door catch assembly in with her thumb. Pretty simple, thanks for having parts like this available to the public!
Was this helpful?
Thank you for voting!
Dryer door catch broke
35 of 49 people
found this instruction helpful.
-
Bill from Houston, TX
- Really Easy
- Less than 15 mins
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this helpful?
Thank you for voting!
My dryer only heats up at the beginning of cycle so my clothes will not dry.
31 of 39 people
found this instruction helpful.
-
Monique from Mission Viejo, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I remove the front control panel and to get to the bottom front dryer door off. Using my volt meter i checked all the sensors and thermal. I surf the internet for hint and some one mention to replace the coil since some time you could have one goes out and the other working still. After i replaced the coil kit it works like a champ.
Was this helpful?
Thank you for voting!
I had bought the portable dishwasher from an add in the paper and unfortunately I was unaware that they require faucet adapters and it was not given to me along with the appliance.
29 of 34 people
found this instruction helpful.
-
Ronald from Chebanse, IL
- Really Easy
- Less than 15 mins
I ordered the part and it fit perfectly!! About five minutes to screw it onto my faucet and problem solved!!!
Was this helpful?
Thank you for voting!
old lint screen -torn at wire mesh
27 of 28 people
found this instruction helpful.
-
Chris from Morgan City, LA
- Really Easy
- Less than 15 mins
Local stores did not have any in supply. Went to Partselect and located lint screen, ordered, received in 3 days. replaced screen, Wife now happy again...
Was this helpful?
Thank you for voting!
no heat
31 of 40 people
found this instruction helpful.
-
rex from streator, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
the ignitor did not glow red checked thermal fuse by exhaust duct. fuse open replaced thermal fuse
Was this helpful?
Thank you for voting!
cocverting natural gas to propane gas
43 of 76 people
found this instruction helpful.
-
Billy from Maryville, TN
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench set
removed burner installed propane orfice and kit as per instruction sheet.
Was this helpful?
Thank you for voting!
Dyer drum doesnt turn
27 of 29 people
found this instruction helpful.
-
Shawn from Akron, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
It was really quite esy remove the screws from the back and pop the top off . then remove 2 top inside screws from the front , lift the front off the sides , support the drum and lift out , you will then see the idler wheels, replace them with the new ones ,replce the tensioner , wrap the belt around the drum, need help putting the drum b
... Read more
ack in the case, have someone hold the drum in place while you lay on the ground and put the belt around the motor pulley and the tensioner on the bottom.you then put the front panel back into place and secure with the 2 inside screws, then put the rest back together in reverse oder. ... hope this helps someone
Read less
Was this helpful?
Thank you for voting!
dryer drum not turning and no air circulating
34 of 51 people
found this instruction helpful.
-
Eric from Fort Dodge, IA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
replaced motor and drum rear seal as well as idler wheels, the old rear drum seal was completly worn out, since I had it all apart, I replaced lint chute and trap seals and belt and tensioner. I spent less money on parts than if I would have bought a new dryer. The motor was the main problem as the bearings were shot.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would dry for 5-10 minuets then no heat
35 of 55 people
found this instruction helpful.
-
Richard from Jerome, MI
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
I tested the dryer coils and found that they were getting a voltage but would not open the gas valve. Coils were not bad but weak. After they warmed up they would not open the gas valve. It took 10 min to repace both coils and the heat sensor.
Other Parts Used:
Was this helpful?
Thank you for voting!
had to replace the motor
31 of 43 people
found this instruction helpful.
-
charles from parker, CO
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Follow the advice given in the partsselect website. However, while removing the blower, my hand slipped into the housing and cut my thumb. Connected the wires to the junction box on the motor but didn't realize that the contacts would hit the drum when reinstalled. The original junction box was at a 90 degree rotation relative to the n
... Read more
ew box. When trying to test the breaker tripped. Using the multitester I found out that I burned out the thermal fuse, and froze the door switch. I replace both those parts and started the dryer and could hear a grinding sound. Inspection revealed that the housing of the motor was rubbing against the drum. Removing the drum yet again, I rotated the housing and replaced the drum. The dryer was finally working well.
Read less
Was this helpful?
Thank you for voting!