1107447 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer Had A Continuous Moan And Vibration
-
Roger from Millis, MA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Wrench set
I disconnected the drive belt from the motor and ran the motor to isolate it from the rest of the mechanisms. This was the noise. I disconnected the water lines and electrical cord,laid the machine front down. I disconnected the motor plug,removed the two bracket to body bolts and lifted the motor out to the bench. I then transferred th
... Read more
e bracket to the new motor and reversed the procedure to install the motor. The most difficult part was raising the machine back up alone,I suggest a helper.
Read less
Was this helpful?
Thank you for voting!
Washer leaking
-
Forrest from Oxford, AL
- Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this.
... Read more
Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.
Read less
Was this helpful?
Thank you for voting!
over fill water
-
ronnie from meriden, CT
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench set
replace the water valve
Was this helpful?
Thank you for voting!
Dryer door switch broken or burned out
-
James from Iota, LA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.
Was this helpful?
Thank you for voting!
Stopped and would not restart / start.
-
Patricia from Duck, WV
- Really Easy
- Less than 15 mins
-
Screw drivers
1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed
... Read more
the previous procedures to complete repair.
Read less
Was this helpful?
Thank you for voting!
Faucet adapter leaked
-
Ed from North East, MD
- Really Easy
- Less than 15 mins
Replaced the faucet adapter, works fine
Was this helpful?
Thank you for voting!
Needed a faucet connector
-
Karen from Lafayette, IN
- Really Easy
- Less than 15 mins
I bought the portable dishwasher on Craigslist, and it didn't have the connector that goes on the kitchen faucet. Ordered it here, got it in a few days, and didn't need any tools - just had to screw it on. Good as gold!
Was this helpful?
Thank you for voting!
Could not fit hoses for portable dishwasher onto existing faucet
-
Trisha from Oklahoma City, OK
- Really Easy
- Less than 15 mins
I knew I needed a faucet adapter, but thought I could just go to my local home depot and get the part...not so much. After 3 trips and not getting the part I truly needed I ordered the part from partselect. I received it literally the day after I ordered it, screwed in place with no tools, attached the coupler/hoses to the faucet and wa
... Read more
shed dishes. I wish I would have ordered the part from partselect before even bother with home depot. I would have saved myself a lot of trouble! Extremely happy! Thank you!
Read less
Was this helpful?
Thank you for voting!
No faucet adapter
-
Michael from Irons, MI
- Easy
- Less than 15 mins
I unsrew the faucet head, and attached th e adapter
Was this helpful?
Thank you for voting!
changed out kitchen sink faucet set
-
George from Cameron, NC
- Really Easy
- Less than 15 mins
replaced the faucet adapter I did not save when I change out the kitchen sink faucet set
Was this helpful?
Thank you for voting!
The Faucet Adapter was worn out.
-
Becky from Stanley, NC
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
Ordered a new Faucet Adapter! Simple
Was this helpful?
Thank you for voting!
A gift portable dishwasher did not have the faucet adapter.
-
Norm from Hamilton Square, NJ
- Really Easy
- Less than 15 mins
-
Pliers
Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't
... Read more
use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.
Read less
Was this helpful?
Thank you for voting!
broken
-
Tomas from Orlando, FL, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Removed the old one installed the new one
Was this helpful?
Thank you for voting!
Switch broken
-
Willie from Virginia Beach, VA
- Difficult
- 1- 2 hours
-
Screw drivers, Socket set
I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the lo
... Read more
cation and design of the switch. I got it though.
Read less
Was this helpful?
Thank you for voting!
Had issues with removing the inner tub
-
Bruce from Yankton, SD
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!
Was this helpful?
Thank you for voting!