11074202201 Kenmore Dryer - Instructions

All Instructions for the 11074202201
121 - 135 of 1554

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud rumble noise while drum was turning
9 of 12 people found this instruction helpful.
  • Marcia from CAmden, NY
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
First I pulled out lint catcher, you will see two screws ,removed two the screws on top ,( philips head screw driver) I than took a putty knife and pushed in the front of the dryer under the lid and lifted the top up, I than removed a self tapping screw on each side with a 5/16 wrench and lifted the front panel out. I than pulled out the drum and this exposed the two rollers, I than pulled of the nut locks with athe pliers , took off the plastic triangle snaps and pullled off the old rollers , replaceing them with the new ones,put the triangle locks on and that the lock nuts on , I than put the drum back in, than the front panel, replaceing the two self tapping screws , snapped down the top,replaced the other two screws again on top and replaced the lint catcher, I was done.
Was this helpful?
Thank you for voting!
Dryer was leaving scorch marks on clothing
8 of 9 people found this instruction helpful.
  • Howard from Tyler, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
UNPLUG THE DRYER!!!!!
First removed the two screws holding the lint filter in place. Then slipped a screw driver between the top and the dryer body to remove the top. Using a nut driver removed the two screws holding the front of the dryer in place, remove the two wires for the door switch., lift the front cover of the dryer and set it aside. Support the drum ( two extra hands would be nice) and remove the drive belt. Then remove the drum. A thorough cleaning to remove all of the scorch like stain from the drum and back plate. Remove the seal and glue the new one in its place. Put it back like you found it. Make sure that the seal is not tucked against the back plate. Dryer works better than new and no more stains.
Was this helpful?
Thank you for voting!
dryer drum belt broke
7 of 7 people found this instruction helpful.
  • Paul from Athens, TX
  • Easy
  • Less than 15 mins
  • Screw drivers
I needed to remove the front lower cover, very easy as it is held on with clips only so I used a flat head screw driver to pop it off. I had to remove the lint filter and then there are two screws attaching the top cover of the dryer to the internal lint filter tray. The top of the dryer can then be opened front to back I again used the flat head screw driver to pop the top open as it has two clips at the front corners. It helps to have someone to hold it open or a rod of some type to keep it open. You can now lay the belt on the top of the drum and work it down the back side by pulling forward on the drum itself to seperate the drum from the seal that presses aginst the back side of the drum. I then went from the lower front to retrieve the belt now draped over the drum and pinched the belt to pass it through the tensioner and over the drive pulley. looking at it from the front the belt will come down the right side of the drum under the tensioner pulley around the drive pulley across the bottom of the drum and up the left side. The belt sits almost in the middle of the drum not against the back lip where there is a groove that might be confused as a place for the belt to ride that is where the seal sits then reverse the process to reattach the top to lint tunnel and reattach front cover and you are good to go . i would suggest vaccuming any old dust/ lint whlie everything is open as this reduces the chance for catching on fire I was supprised as to how much lint was loose inside the dryer cavity itself and our dryer is gas and the flame is an open flame.
Was this helpful?
Thank you for voting!
The dryer door latch broke
9 of 13 people found this instruction helpful.
  • Theresa from Topeka, KS
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.
Was this helpful?
Thank you for voting!
gas dryer would fire, but shut down before getting warm enough to dry clothes
7 of 7 people found this instruction helpful.
  • Glenn from Ossian, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set, Wrench set
Removed lower front cover of dryer, located coils, removed old coils by disconnecting the wires and removing the hold down bracket screws. Pulled the old coils out replaced them with the new coils by aligning the index pins on the coils with the holes in the bracket then reattached the bracket and plugged the wires into the new coils. The n closed the cover on the front of the dryer. Dryer now ignites and stays on to heat up and dry clothes.
Was this helpful?
Thank you for voting!
Dryer hummed but drum wouldn't turn unless helped.
8 of 10 people found this instruction helpful.
  • Leo from Ellicott City, MD
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.
Was this helpful?
Thank you for voting!
No heat
9 of 13 people found this instruction helpful.
  • Philip from La Palma, CA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench set
Took everything apart, replaced the igniter flint, and still didn't get heat. Then found out the thermal sensor wasn't running a electrical current through it with voltmeter and just replaced that, now it we have heat again!
Was this helpful?
Thank you for voting!
Dryer motor siezed up, from age and wear
9 of 13 people found this instruction helpful.
  • S.K. Mechancil Company from Pittsfield, MA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Troubleshhot problem, used multimeter to verify current to motor. Once that i was sure motor was getting proper voltage, I used a meg-ohm meter on A/C motor windings and physically tried to turn motor and found that it was siezed. I then cleaned inside of unit inspected belt and drum rollors. Due to the cost of the items, I decided If I w as going to replace the motor I should replace all moving parts, and install new belt. Everything went easy. WHAT WAS MOST IMPRESSIVE! was that the Parts people sent the correct parts on time the first time, with no hiddin charges. There web site should accurate diagrams of parts and internals of machine. I was really pleased and will use this service again. Thank you
Was this helpful?
Thank you for voting!
Dryer not Drying
8 of 10 people found this instruction helpful.
  • Manuel from Jurupa Valley, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Replaced both Coils. Purchased M Series coils much less expensive buying coils together instead of seperately. Problem solved.
Was this helpful?
Thank you for voting!
My Kenmore dryer door catch was worn out, so the dryer door wouldn't stay closed, and I was unable to dry my laundry.
8 of 11 people found this instruction helpful.
  • Carol from Golden Valley, MN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.
Was this helpful?
Thank you for voting!
the glow ignitor would not cycle on
7 of 8 people found this instruction helpful.
  • Georgio from Oradell, NJ
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers
I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the g low plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.
Was this helpful?
Thank you for voting!
Dryer wouldn't start
10 of 17 people found this instruction helpful.
  • Ryan from Mundelein, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
My 80 series Kenmore dryer wouldn't start so I looked online for a solution to the problem. One of the sites I found stated that the problem could be as simple as a thermal fuse if other potential issues could be ruled out. I ordered the part on a Monday from PartSelect with standard FedEx ground shipping - stated it could be 3-5 busine ss days. To my amazement, the part arrived the next day! Awesome!!! I watched the video on the PartSelect site to make sure I knew how to fix it, then followed the easy instructions. All I needed to do was use the nutdriver to remove the back cover from the dryer, unplug the two wires going into the thermal fuse, remove the old fuse, and pop the new one in. Then I just plugged the wires into the new fuse, replaced the cover and voila, the dryer worked like a champ! Thank you PartSelect for saving me a needlessly high repair bill!!
Was this helpful?
Thank you for voting!
No Heat After 10 Minutes
7 of 8 people found this instruction helpful.
  • lawrence from GROTON, VT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Wrench set
Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.
Was this helpful?
Thank you for voting!
no heat was being produced
9 of 14 people found this instruction helpful.
  • reinaldo from guttenberg, NJ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website
Was this helpful?
Thank you for voting!
broken rib belt
6 of 6 people found this instruction helpful.
  • Robert from PEABODY, MA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Followed instructions from video, just removed lint collector, dryer top and front panel, removed broken belt and old idler pulley. Vacuumed and cleaned up inside dryer.installed new pulley and rib belt according to printed instructions,installed new dryer duct and new clamps. Saved myself huge service call or having to buy new dryer.Wil l be checking with this site on any future repairs instead of calling a repair service. Your video made it real easy to repair.and I am 77 years old.. Bob
Was this helpful?
Thank you for voting!
All Instructions for the 11074202201
121 - 135 of 1554