110733 Kenmore Washer - Instructions

All Instructions for the 110733
31 - 45 of 49

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
washer would fill with water but not start
5 of 15 people found this instruction helpful.
  • Edward from Nanuet, NY
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at
Was this helpful?
Thank you for voting!
Dryer would not activate
2 of 7 people found this instruction helpful.
  • Andris from Sands Point, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
Was this helpful?
Thank you for voting!
Missing lid hinge bearing
  • Kim from Oviedo, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid an d into bushing. 5)Reinstall hinge pin retaining screws and tighten.
Was this helpful?
Thank you for voting!
Washer leaking
  • Forrest from Oxford, AL
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.
Was this helpful?
Thank you for voting!
over fill water
  • ronnie from meriden, CT
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
replace the water valve
Was this helpful?
Thank you for voting!
Dryer door switch broken or burned out
  • James from Iota, LA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.
Was this helpful?
Thank you for voting!
Stopped and would not restart / start.
  • Patricia from Duck, WV
  • Really Easy
  • Less than 15 mins
  • Screw drivers
1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed the previous procedures to complete repair.
Was this helpful?
Thank you for voting!
Faucet adapter leaked
  • Ed from North East, MD
  • Really Easy
  • Less than 15 mins
Replaced the faucet adapter, works fine
Was this helpful?
Thank you for voting!
Needed a faucet connector
  • Karen from Lafayette, IN
  • Really Easy
  • Less than 15 mins
I bought the portable dishwasher on Craigslist, and it didn't have the connector that goes on the kitchen faucet. Ordered it here, got it in a few days, and didn't need any tools - just had to screw it on. Good as gold!
Was this helpful?
Thank you for voting!
Could not fit hoses for portable dishwasher onto existing faucet
  • Trisha from Oklahoma City, OK
  • Really Easy
  • Less than 15 mins
I knew I needed a faucet adapter, but thought I could just go to my local home depot and get the part...not so much. After 3 trips and not getting the part I truly needed I ordered the part from partselect. I received it literally the day after I ordered it, screwed in place with no tools, attached the coupler/hoses to the faucet and wa shed dishes. I wish I would have ordered the part from partselect before even bother with home depot. I would have saved myself a lot of trouble! Extremely happy! Thank you!
Was this helpful?
Thank you for voting!
No faucet adapter
  • Michael from Irons, MI
  • Easy
  • Less than 15 mins
I unsrew the faucet head, and attached th e adapter
Was this helpful?
Thank you for voting!
changed out kitchen sink faucet set
  • George from Cameron, NC
  • Really Easy
  • Less than 15 mins
replaced the faucet adapter I did not save when I change out the kitchen sink faucet set
Was this helpful?
Thank you for voting!
The Faucet Adapter was worn out.
  • Becky from Stanley, NC
  • Really Easy
  • Less than 15 mins
  • Wrench (Adjustable)
Ordered a new Faucet Adapter! Simple
Was this helpful?
Thank you for voting!
A gift portable dishwasher did not have the faucet adapter.
  • Norm from Hamilton Square, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers
Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.
Was this helpful?
Thank you for voting!
Switch broken
  • Willie from Virginia Beach, VA
  • Difficult
  • 1- 2 hours
  • Screw drivers, Socket set
I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the lo cation and design of the switch. I got it though.
Was this helpful?
Thank you for voting!
All Instructions for the 110733
31 - 45 of 49