11073036102 Kenmore Dryer - Instructions

First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of ... Read more needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes.

i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service

Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and did ... Read more n't take but 15-20 minutes.

Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.

Pryed dryer top open and opened front door. . Unscrewed the 2 retaining screws. Pulled old switch from the wiring harness. Put new switch in place and replaced the retaining screws. Put new switch wire plug into the wiring harness. Before closing top, checked door switch function with dryer on. Dryer cut off when door open an ... Read more d when closed dryer started normally. . . Maint. Note instruction book should warn that letting door slam, which I did on occaision, broke the switch arm. Might save future problems.

Followed electrical drawing from switch to motor, Thermal fuse was in the line and no power coming through it, removed wire and put together and tested, dryer turned on. Read statements from others at parts select and also bought thermostat because time stopped working last year. Installed both parts and cleaned dryer, works perfect inclu ... Read more ding timer.

It was simple once I figured out what to do:). I removed the 2 screws on the top of the dryer... they were a bit hard to find. Even with the other descriptions on this site. I was removing things I didn't need to. The 2 screws you need to remove are under the LINT COLLECTOR LID. Remove those 2 screws & lift the lid... it will be tigh ... Read more t at first. the front of the lid has 2 "catches" in the corners.

The hardest part was getting the door switch assembly to "unplug". We pried it off -- eventually -- & then simply plugged in the new one.

Saved me LOTS of money & was worth the 30 minutes - 1 hour of work.

As I said previously, once you realize how to get the lid up & manage to pry off the plug, that's all there is to it -- easy!

Save yourself time & money & do it yourself!

When my dryer suddenly stopped functioning, without any prior signs of pending failure, I guessed that it had to be something simple, like a fuse. I did a google search and stumbled across a forum post that described the symptoms (wouldn't turn on), and the poster said that Whirlpool recommends replacing the thermostat whenever the fuse ... Read more is replaced. The reason for this is that the likely cause of the fuse burning is that the thermostat is no longer properly regulating the temperature range of the heating element.

I disconnected the power source, and then I removed the back cover, and both parts were in plain view, so I simply replaced the wires one by one.

ordered new lint screen, removed old screen, inserted new screen.

I first unplugged the electrical plug, then opened up the dryer, front and back. Once I had diagnosed the problem I unscrewed the thermal fuses and thermostat. Marked which color wire went to which connector and continued to replace one wire at a time. Re-attached the mounting screws, verified all wires were connected, plugged in dryer ... Read more to test heat cycle. Once the dryer worked correctly I vacuumed all lint and covered it up.

I can't believe I waited so long to find this part and do this. I got the package very fast, opened it, took the piece to my dryer and popped it into place with my fingers. It worked perfectly! this took all of two minutes and saved me from having to hold the dryer door closed with a stick. Thank you, thank you!!!

I spent nearly an hour trying to self-diagnose the problem before I wised up and found PartSelect.com. After reading just a couple of postings I went back and tested the thermal fuse. It was bad. Other posts suggested I replace the thermostat at the same time, so I ordered both. The parts arrived within three days and the actual repai ... Read more r took less than 10 minutes.

First unplug your dryer. Then, I removed the two screws on the lint trap leaving the lint trap in place--do not pull out the lint trap--only remove the two screws. Next, slide the top of the dryer slightly forward in order to release the top of the dryer. I did this with my hands. Once the top of the dryer is released, raise the top of t ... Read more he dryer and unplug the door switch assembly. Then, remove the two screws that hold the switch. These two screws were located on the front panel of my dryer and are visible when you open the dryer door. Remove the old switch and install the new switch by putting the two screws you previously took out from the old switch back in place and plug in the new switch. Lower the dryer top. Push the top back to lock in place. Line up the lint trap holes for the two screws that hold it in place and replace those screws. Plug your dryer back in and it should work properly. Very easy repair. We ordered our part one morning before noon, and it was here the next afternoon with regular shipping. GREAT SERVICE.

The issue was the idler pulley. First I began opening up the front panel based on a youtube video but soon realized the model was slightly different and required a lot more items to remove. I saw the pulley in the back with nothing in the way so I put the front panel crap back on and removed the rear panel. There it was, very simple to re ... Read more move and replace. I'm not looking forward to drum rollers though. Hopefully they're aren't as difficult as they appear.

Turned off the power.Pulled the dryer out, removed the screws from the control cover panel, unplugged the switch, pressed the release clip the did the opposite to install new switch. Replaced the back panel, put the nob on and it looks as good as new.Turned on the power.