1107301 Kenmore Dryer - Instructions

All Instructions for the 1107301
16 - 30 of 1399

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer would not heat.
156 of 174 people found this instruction helpful.
  • Russell from LA VERNE, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
I checked parts select.com and followed the guide lines,ordered the correct parts thanks to the web site help.parts arrived in 2 days,A very easy install and back to work drying clothes.Thanks parts select.
Was this helpful?
Thank you for voting!
Timer wasn't working (New Timer)
168 of 214 people found this instruction helpful.
  • Joaquin from Las Vegas, NV
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver
Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I or dered the coils for the valves, replaced both valves and tested the dryer and it work just like when I first bought the appliance.
Was this helpful?
Thank you for voting!
When I opened my dryer door while it was running, the drum continued to turn and the light would not come on.
158 of 225 people found this instruction helpful.
  • Baxter from Goodlettsville, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First unplug your dryer. Then, I removed the two screws on the lint trap leaving the lint trap in place--do not pull out the lint trap--only remove the two screws. Next, slide the top of the dryer slightly forward in order to release the top of the dryer. I did this with my hands. Once the top of the dryer is released, raise the top of t he dryer and unplug the door switch assembly. Then, remove the two screws that hold the switch. These two screws were located on the front panel of my dryer and are visible when you open the dryer door. Remove the old switch and install the new switch by putting the two screws you previously took out from the old switch back in place and plug in the new switch. Lower the dryer top. Push the top back to lock in place. Line up the lint trap holes for the two screws that hold it in place and replace those screws. Plug your dryer back in and it should work properly. Very easy repair. We ordered our part one morning before noon, and it was here the next afternoon with regular shipping. GREAT SERVICE.
Was this helpful?
Thank you for voting!
Extended drying time. Some but not enough heat. Burner would light for 15-18 seconds at first then shut off for 1-3 minutes then light for 3-6 seconds and repeat for the length of the cycle.
128 of 148 people found this instruction helpful.
  • Matthew from Lake Worth, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers
Determining the problem was the hardest part. With multiple parts (coils,thermostats...)possibly causing similar symptoms, I narrowed it down to the two coil valves.
Un plug the dryer. Remove two screws at the base of the front panel. Turn the front panel 180 degrees to avoid disconnecting the door switch. Gas valve with coils on top are on the right in front. Remove two screws in bracket holding coils, disconnect the wires, replace with new coils and reconnect wires. One coil has 2 terminals the other has 3 no chance of crossing the wires. I used an offset/right angle screw driver for one of the bracket screws due to close proximity to the drum. A stubby phillips head will work. You can check the burner operation with the front panel off as long as the door switch is still attached. Swing the front panel around and lift back into place securing with the two screws. Dryer works fine now.
Was this helpful?
Thank you for voting!
very loud squeeling sound
110 of 120 people found this instruction helpful.
  • jason from HOLDEN, MA
  • Really Easy
  • 30 - 60 mins
  • Socket set
The issue was the idler pulley. First I began opening up the front panel based on a youtube video but soon realized the model was slightly different and required a lot more items to remove. I saw the pulley in the back with nothing in the way so I put the front panel crap back on and removed the rear panel. There it was, very simple to re move and replace. I'm not looking forward to drum rollers though. Hopefully they're aren't as difficult as they appear.
Was this helpful?
Thank you for voting!
Broke start switch while moving
109 of 118 people found this instruction helpful.
  • Dennis from Port Orchard, WA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Turned off the power.Pulled the dryer out, removed the screws from the control cover panel, unplugged the switch, pressed the release clip the did the opposite to install new switch. Replaced the back panel, put the nob on and it looks as good as new.Turned on the power.
Was this helpful?
Thank you for voting!
dryer door would not stay shut
103 of 107 people found this instruction helpful.
  • Pam from Woodbridge, VA
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.
Was this helpful?
Thank you for voting!
door switch actuator spring broken
92 of 100 people found this instruction helpful.
  • Paul from Vero Beach, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
-unplugged appliance
-removed lint trap
-removed 2 lint trap shute screws with phillips screwdriver
-popped open top of appliance with standard screwdriver by applying pressure at each front corner so that it could be tilted up to access actuator switch on right side of door
-removed 2 actuator switch screws, located o n upper right side of laundry door, with phillips screwdriver (screws are accessed from outside of door frame not through appliance top).
-discarded broken actuator spring (accessed from open appliance top)
-replaced new actuator spring
-replaced 2 actuator switch screws
-closed top
-replaced 2 lint trap shute screws
-replaced lint trap
-plugged in appliance
-tested for operation
-kissed by happy wife
Was this helpful?
Thank you for voting!
Squeaky Dryer Noise
94 of 106 people found this instruction helpful.
  • Eddie from PELZER, SC
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
I purchased the dryer repair kit with the drum belt, wheels and idler pulley. I watched the instructional videos online and it seemed fairly straight forward. Breaking down the dryer and replacing the pulleys was easy enough. My problem began when I tried to feed the drum belt around the idler pulley. After finishing the job, the dryer wo uld not turn and the sensor light stayed on. I thought something else was broken with the dryer and spent hours trouble shooting other problems that I was having. Finally I figured out that the drum belt was not installed correctly around the idler pulley. However, I could not get it properly installed from the front of the machine so I tried from the rear still with no avail. I finally had to fish the old belt out of the garbage can that I had thrown away earlier. I lined up the old belt with the new one in the kit and discovered that the new belt was much smaller, so I put the old one back on the drum. Here's the lesson I learned...make sure the belts are the same size before attempting to install. The old idler was responsible for the squeaking and that stopped but I am still using the same old drum belt. Hope it lasts.
Was this helpful?
Thank you for voting!
Dryer would only heat cycle once
90 of 101 people found this instruction helpful.
  • Robert from Seattle, WA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I removed the two screws holding the front panel to expose the lower works and verified the heating cycle failure. After a check of the vent system, checking the sensors for continuity and coils for resistance, I retired to the 'net for support. Accepting the general consensus that the most frequent, common and likely failure to be the c oils, I rechecked them with the meter and found the two pronged coil to have significantly more resistance than the three prong coil. That was enough evidence to point to the coils. While I waited for the part to arrive, I replace the vent ducting. When the parts arrived I removed the two Phillips screws holding the coils, removed the old ones, installed the new ones, replaced the bracket, put the front cover back on and in less then ten minutes clothes where drying.
Was this helpful?
Thank you for voting!
dryer wouldn't dry
110 of 191 people found this instruction helpful.
  • JEFFERY from ABINGDON, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
un pluged it then removed the hose took the back off took out the 2 screws out of each part replace it with the new parts , then pluged it back to make sure it would work and it did the very first time. i'm 1 happy roper owner.
Was this helpful?
Thank you for voting!
Very Loud Squeaking Noise
79 of 100 people found this instruction helpful.
  • GREGORY from Wilsonville, OR
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
1) Disconnected power cord from wall. 2) Disconnected vent hose from back of dryer. 3)Removed dryer rear panel. 4)Disengaged tension spring on idle wheel arm. 5) Removed worn idle wheel. 6)Installed new Idler wheel assembly. 7) Vacuumed dust from rear of dryer (optional, recommended). 8) Reinstalled rear cover, vent hose and power cord. E asy repair 15-30
Was this helpful?
Thank you for voting!
Door switch did absolutely nothing....dryer kept running
98 of 166 people found this instruction helpful.
  • Clark from Melbourne, FL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I read a fix-it article from another contributor and followed those instructions to the T. Pull out lint trap, remove the two screws. Slide the top cover towards the front and prop it up with a mop handle.
Unscrew two screws in the door switch (with the door open) - Oh, to keep from killing yourself unplug the dryer just in case. Take pliers and pull the plug apart. It will be right in front of you in the right corner at the top. Plug new switch into that plug, reinstall the switch by reinstalling the two screws you removed. Snap top back into place and reinstall the two screws at the lint trap. Oh, don't forget to clean the trap and slide it back into the unit. Now you have earned that beer.
Put tools away and proudly show your job off to the wife telling her how difficult it was.
Was this helpful?
Thank you for voting!
Door won't latch
95 of 158 people found this instruction helpful.
  • Jill from bellevue, WA
  • Really Easy
  • Less than 15 mins
  • Pliers
I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks
Was this helpful?
Thank you for voting!
The dryer heated up for a few minutes and then cooled down.
67 of 76 people found this instruction helpful.
  • James from Limington, ME
  • A Bit Difficult
  • Less than 15 mins
  • Screw drivers
1 Unplug power.
2. Remove the front of the unit by removing the two screws at the bottom of the front panel. Front dryer panel will swing out from the bottom and then the clips will release the top of the panel, careful not to disconnect the dryer door switch. ( can be unplugged to remove the front panel out of the way.)
3. Look ing inside the unit on the right side you will see the gas value. On top of the gas unit you will see two small coils the coil closest to the burner has two leads on it. Remove the two screws to get to the coils, remove the medal plate, remove the connector then lift off the secondary coil. Replace and test. You can test unit with the front panel off. (be careful). If no heat, check that the Flat Style igniter is glowing. (ohm out both coils) before ordering parts. Intermittent heat problems. I replaced the secondary coil, it did ohm out o:k but it had swollen and was very tight on the shaft.
Was this helpful?
Thank you for voting!
All Instructions for the 1107301
16 - 30 of 1399