1107293 Kenmore Dryer - Instructions

All Instructions for the 1107293
76 - 90 of 644

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer gasket detached from screen
14 of 17 people found this instruction helpful.
  • Richard from Duarte, CA
  • Really Easy
  • Less than 15 mins
Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.
Was this helpful?
Thank you for voting!
Burner would not go on on my Stack Set Dryer
16 of 24 people found this instruction helpful.
  • Robert from North East, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!
Was this helpful?
Thank you for voting!
Lint has been bypassing the lint filter and building up in the fan (and duct)
12 of 12 people found this instruction helpful.
  • David from PINETOWN, NC
  • Really Easy
  • Less than 15 mins
I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.
Was this helpful?
Thank you for voting!
Door latch (female part) was broken.
11 of 11 people found this instruction helpful.
  • JEANMARIE from BELLEROSE, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
dryer not heating up
12 of 14 people found this instruction helpful.
  • Richard from New Windsor, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helpi ng me out!!!
Was this helpful?
Thank you for voting!
The Dryer would not get hot.
14 of 20 people found this instruction helpful.
  • Jerry from Bradenton, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.
Was this helpful?
Thank you for voting!
The dryer was not fully drying
12 of 14 people found this instruction helpful.
  • Michael from Chicago, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.
Was this helpful?
Thank you for voting!
Rear dryer drum seal came out
17 of 29 people found this instruction helpful.
  • William from Pontiac, MO
  • Easy
  • More than 2 hours
  • Screw drivers, Socket set
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Was this helpful?
Thank you for voting!
When using the dryer the cycle would stop and display E1 as the reason
13 of 18 people found this instruction helpful.
  • Joyce from Holbrook, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.
Was this helpful?
Thank you for voting!
The Dryer stopped working completely.
13 of 18 people found this instruction helpful.
  • Elyse from Chicago, IL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I looked up the procedure to remove the switch in a repair book, removed the broken switch. Then I reconnected the wire leads, put the part in and closed everything up. The part arrived so quickly and there were even instructions with the part which made the repair go so easily.
Was this helpful?
Thank you for voting!
Timer would stop the dryer with in 1 minute after set
16 of 27 people found this instruction helpful.
  • Romeo from Holland, MI
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Opened the back cover. Unscrewed the timer replaced the wires connected on the old timer to the new timer. Screwed the new timer in place screwed the cover back on. Then placed the timer nob on the front.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Dryer motor would not run
14 of 22 people found this instruction helpful.
  • David from Berkeley Springs, WV
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The motor relay arrived the day after I ordered it, and i had not requested expedited shipment. Thanks for the quick delivery.
I say the repair was a bit difficult only because it was not obvious at all how to open up the control console, and the user's manual was completely silent on the subject of disassembly . I finally found that the retaining end caps simply snapped off. Once the console was open, I found that the DIY instructions were folded up inside the console. Replacing the part only took about ten minutes. Now that I know how to open the console, the whole repair could be done in less than fifteen minutes.
Was this helpful?
Thank you for voting!
Washer stopped working mid cycle restarts after resetting lid
12 of 17 people found this instruction helpful.
  • Eric from West Chester, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.
Was this helpful?
Thank you for voting!
Gas Dryer would heat for one heating cycle but no gas afterward. Ignitor would glow.
10 of 12 people found this instruction helpful.
  • Jim from Foothill Ranch, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Checked four thermocouples all showed continuity with my multimeter so they were all good. I'd read that the coils commonly went out and that these were the symptoms. Hey, it's very simple in there. Not much else could be wrong. I had a Maytag repairman come out. At first he said the problem was a blocked vent. I knew he was wrong. Then h e said one of the thermocouples went out. It was $80 for him to come out. It turned out that his second diagnosis was wrong too. To repair the dryer by Maytag would have cost me $240. I gave him $80 and bought the coils for $37. They are EXTREMELY easy to replace: two screws held a bracket that held two coils. With the bracket off, I took off the old coils and slid on the new ones.
Was this helpful?
Thank you for voting!
All Instructions for the 1107293
76 - 90 of 644