1107288 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer making extra noise while running
91 of 102 people
found this instruction helpful.
-
Michael from Haines City, FL
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench (Adjustable)
1st Unpluged power.
2nd removed two screws under lint screen cover.
3rd poped up lid with flathead screwdryer, then removed (2) 5/16 screws from door cover and unpluged lid switch, lifted up dryer door pannel
4th removed drum
5th took out plastic triangle wheel rings
6th removed old belt guild (to motor pully)
... Read more />7th removed old wheels and plastic rings stops
8th cleaned excessive hair dust with shopvac
9th put new replaicment part in dryer. made sure to turn manually to make sure belt was lined up properly, then put all dryer peices back.
10th aditional work, took back cover off and removed the (4) 1/4 screws for lint screen case (left side in dryer) vacumed out any excessive dirt lint ect, also cleaned any excessive dust I found in back of dryer, dryer , exhaust ect, and put all back together.
JUst like a new dryer aain after all PM was complete.
2nd removed two screws under lint screen cover.
3rd poped up lid with flathead screwdryer, then removed (2) 5/16 screws from door cover and unpluged lid switch, lifted up dryer door pannel
4th removed drum
5th took out plastic triangle wheel rings
6th removed old belt guild (to motor pully)
... Read more />7th removed old wheels and plastic rings stops
8th cleaned excessive hair dust with shopvac
9th put new replaicment part in dryer. made sure to turn manually to make sure belt was lined up properly, then put all dryer peices back.
10th aditional work, took back cover off and removed the (4) 1/4 screws for lint screen case (left side in dryer) vacumed out any excessive dirt lint ect, also cleaned any excessive dust I found in back of dryer, dryer , exhaust ect, and put all back together.
JUst like a new dryer aain after all PM was complete.
Read less
Was this helpful?
Thank you for voting!
Dryer would only heat cycle once
90 of 101 people
found this instruction helpful.
-
Robert from Seattle, WA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I removed the two screws holding the front panel to expose the lower works and verified the heating cycle failure. After a check of the vent system, checking the sensors for continuity and coils for resistance, I retired to the 'net for support. Accepting the general consensus that the most frequent, common and likely failure to be the c
... Read more
oils, I rechecked them with the meter and found the two pronged coil to have significantly more resistance than the three prong coil. That was enough evidence to point to the coils. While I waited for the part to arrive, I replace the vent ducting. When the parts arrived I removed the two Phillips screws holding the coils, removed the old ones, installed the new ones, replaced the bracket, put the front cover back on and in less then ten minutes clothes where drying.
Read less
Was this helpful?
Thank you for voting!
Broken belt - drum would not turn
87 of 101 people
found this instruction helpful.
-
Gary from Oakland, MD
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcer
... Read more
ting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.
Read less
Was this helpful?
Thank you for voting!
dryer wouldn't dry
110 of 191 people
found this instruction helpful.
-
JEFFERY from ABINGDON, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
un pluged it then removed the hose took the back off took out the 2 screws out of each part replace it with the new parts , then pluged it back to make sure it would work and it did the very first time. i'm 1 happy roper owner.
Other Parts Used:
Was this helpful?
Thank you for voting!
Door won't latch
95 of 158 people
found this instruction helpful.
-
Jill from bellevue, WA
- Really Easy
- Less than 15 mins
-
Pliers
I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks
Was this helpful?
Thank you for voting!
The dryer heated up for a few minutes and then cooled down.
67 of 76 people
found this instruction helpful.
-
James from Limington, ME
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
1 Unplug power.
2. Remove the front of the unit by removing the two screws at the bottom of the front panel. Front dryer panel will swing out from the bottom and then the clips will release the top of the panel, careful not to disconnect the dryer door switch. ( can be unplugged to remove the front panel out of the way.)
3. Look ... Read more ing inside the unit on the right side you will see the gas value. On top of the gas unit you will see two small coils the coil closest to the burner has two leads on it. Remove the two screws to get to the coils, remove the medal plate, remove the connector then lift off the secondary coil. Replace and test. You can test unit with the front panel off. (be careful). If no heat, check that the Flat Style igniter is glowing. (ohm out both coils) before ordering parts. Intermittent heat problems. I replaced the secondary coil, it did ohm out o:k but it had swollen and was very tight on the shaft.
2. Remove the front of the unit by removing the two screws at the bottom of the front panel. Front dryer panel will swing out from the bottom and then the clips will release the top of the panel, careful not to disconnect the dryer door switch. ( can be unplugged to remove the front panel out of the way.)
3. Look ... Read more ing inside the unit on the right side you will see the gas value. On top of the gas unit you will see two small coils the coil closest to the burner has two leads on it. Remove the two screws to get to the coils, remove the medal plate, remove the connector then lift off the secondary coil. Replace and test. You can test unit with the front panel off. (be careful). If no heat, check that the Flat Style igniter is glowing. (ohm out both coils) before ordering parts. Intermittent heat problems. I replaced the secondary coil, it did ohm out o:k but it had swollen and was very tight on the shaft.
Read less
Was this helpful?
Thank you for voting!
No heat to dry clothes
66 of 77 people
found this instruction helpful.
-
Karen from Pine Mtn. Club,, CA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
First I took the front of the dryer off then located the igniter. It only required removing two screws, removing old igniter, replacing with new igniter, and replacing the two screws.. While I was replacing the igniter I took the drum out and throughly cleaned the inside. Lucky me, I found 85 cents on the floor of the dryer. I am 65yr
... Read more
s old, married and mother of two.
This was easy to do and sure saved money. I reccommend others try to do repairs for themselves and using PartSelect was less expensive too.
This was easy to do and sure saved money. I reccommend others try to do repairs for themselves and using PartSelect was less expensive too.
Read less
Was this helpful?
Thank you for voting!
drum stopped turning on dryer
62 of 73 people
found this instruction helpful.
-
Matthew from East Islip, NY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Great! Spent about $36.00 and I ended up with a overhauled dryer. I ended up cleaning the whole thing out, it's amazing how much stuff accummulates in the frame of a dryer, I also found about $2.00 in change. It's a good idea to clean out a dryer every few years and the broken belt forced me to do it.
But anyway the parts ca ... Read more m very quick and had easy to follow directions.
I would reccomend part select. Matt
But anyway the parts ca ... Read more m very quick and had easy to follow directions.
I would reccomend part select. Matt
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Replacing worn drum support rollers and shafts.
60 of 69 people
found this instruction helpful.
-
Gary from Canton, CT
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Very easy once I figured out how to open it up to see what was the matter.
1 Remove power.
2 Open the lint filter cover and remove the 2 Phillip screws.
3 Pry the front of the top cover up to separate the cover from the plastic clips that secure to the top front panel.
4 Remove the 2 nut screws securing the top of the ... Read more front panel to each side cover.
5 Pull front panel out slightly to detach wiring from the cover switch.
6 Pull front panel straight up and set aside.
7 Remove drum belt from tensioner and motor pulley under the drum.
8 Remove drum by pulling it toward the front between the 2 sides.
9 Locate the 2 support rollers and their mounting shafts. Change the shafts at this point if they are worn. (Mine were OK)
10 Remove the support bracket from the shaft if present.
11 Remove the plastic triangular retainer from the shaft and slide the old wheel off of the shaft.
12 Clean the shaft from any bearing debris.
13 Replace the rollers and retainers.
14 Insert drum through the front side panels making sure the seal on the rear of the drum is centered around the opening and not folded inside the opening.
15 Place the belt on the drum and thread the belt through the tensioner and around the motor pulley.
16 Position the front cover on the lower clips on each of the sides.
17 Re-attach the 2 wires for the cover switch.
18 Pull the drum up so the opening on the drum and front cover align.
19 Screw together the side panels to the front panel using the 2 hex headed screws.
20 Check for binds by rotating the drum several times by hand.
21 Press the front of the top panel down toward the front panel to engage the plastic clips attaching the top to the front. Watch for the lint filter housing alignment as you push the top panel down.
22 Replace the 2 screws to attach the lint filter to the top cover.
23 Plug in machine and test.
Good luck, It s not as bad as it sounds.
1 Remove power.
2 Open the lint filter cover and remove the 2 Phillip screws.
3 Pry the front of the top cover up to separate the cover from the plastic clips that secure to the top front panel.
4 Remove the 2 nut screws securing the top of the ... Read more front panel to each side cover.
5 Pull front panel out slightly to detach wiring from the cover switch.
6 Pull front panel straight up and set aside.
7 Remove drum belt from tensioner and motor pulley under the drum.
8 Remove drum by pulling it toward the front between the 2 sides.
9 Locate the 2 support rollers and their mounting shafts. Change the shafts at this point if they are worn. (Mine were OK)
10 Remove the support bracket from the shaft if present.
11 Remove the plastic triangular retainer from the shaft and slide the old wheel off of the shaft.
12 Clean the shaft from any bearing debris.
13 Replace the rollers and retainers.
14 Insert drum through the front side panels making sure the seal on the rear of the drum is centered around the opening and not folded inside the opening.
15 Place the belt on the drum and thread the belt through the tensioner and around the motor pulley.
16 Position the front cover on the lower clips on each of the sides.
17 Re-attach the 2 wires for the cover switch.
18 Pull the drum up so the opening on the drum and front cover align.
19 Screw together the side panels to the front panel using the 2 hex headed screws.
20 Check for binds by rotating the drum several times by hand.
21 Press the front of the top panel down toward the front panel to engage the plastic clips attaching the top to the front. Watch for the lint filter housing alignment as you push the top panel down.
22 Replace the 2 screws to attach the lint filter to the top cover.
23 Plug in machine and test.
Good luck, It s not as bad as it sounds.
Read less
Was this helpful?
Thank you for voting!
door kept coming open dryer shuts off
95 of 176 people
found this instruction helpful.
-
RONALD from SALMON, ID
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
use screwdriver topry plastic out plyers to pull out metal latch put new parts in
Was this helpful?
Thank you for voting!
The dryer would start to heat then the heat would stop
58 of 70 people
found this instruction helpful.
-
Theodore from Riverside, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench set
I changed out the cycling thermostat and the high limit thermostat. Mainly because that was what my research indicated was the problem. I then found some more information online that indicated the gas solenoid valves were bad. I ordered them from you and replaced them. The problem was fixed.
In order to replace the valves ... Read more you need to remove the top panel. Two screws at the top of the front door assembly hold it on. Remove the screws, lift up on the front panel door assembly and move it to the side. The drum will rest in place. In the lower left corner, under the drum, you will see the solenoids. Two screws attach a plate that holds down the solenoids. Take the hold down plate off, disconnect the control wires attached to the solenoids and lift out the solenoid/control valves. To assemble everything, work backwards to the start. Good Luck
In order to replace the valves ... Read more you need to remove the top panel. Two screws at the top of the front door assembly hold it on. Remove the screws, lift up on the front panel door assembly and move it to the side. The drum will rest in place. In the lower left corner, under the drum, you will see the solenoids. Two screws attach a plate that holds down the solenoids. Take the hold down plate off, disconnect the control wires attached to the solenoids and lift out the solenoid/control valves. To assemble everything, work backwards to the start. Good Luck
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
dryer would get hot for a while, then quit heating
56 of 70 people
found this instruction helpful.
-
Sharon from Houston, TX
- Easy
- 15 - 30 mins
-
Screw drivers
After reading about other people with this same problem I took a chance that this would be what was wrong with my dryer.I took off the front cover of the dryer by removing two screws. I located the faulty coils and simply plugged in the 2 new coils Tah-dah Probably coud have been done without even removing the front panel, but since it
... Read more
was off I vacuumed out the lint ( actually my husband did all of the above, but I tell a better tale than he does and I diagnosed the problem and ordered theparts)
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer wouldn't turn on
49 of 64 people
found this instruction helpful.
-
Olive from Williamsburg, OH
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the back of the dryer taking off the screws. Found the disposable thermal fuse. Unplugged the 2 blue wires connected to it. Removed the screws holding the part in. Replaced the old part. Reattached the blue wires. Put the back on the dryer. And voila! That simple!
I'm a 39 year old woman with absolutely no patience fo ... Read more r tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.
I'm a 39 year old woman with absolutely no patience fo ... Read more r tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.
Read less
Was this helpful?
Thank you for voting!
door switch - broken tab
44 of 50 people
found this instruction helpful.
-
Nick from Reynoldsburg, OH
- Easy
- Less than 15 mins
-
Screw drivers
Unplugged dryer, removed two screws from the lint trap area, pried up the top of the dryer to get to the switch, removed two screws securing the switch, unplugged the switch, plugged in the new one and reversed the procedure.
Was this helpful?
Thank you for voting!
Gas Flame Would Drop Out
49 of 66 people
found this instruction helpful.
-
FRED from BRIELLE, NJ
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
First it was a process of alimination to find out why it was dropping out. After the problem was found it was just a matter of replacing the holding coil on the gas valve. Thank you fred kenney sr
Was this helpful?
Thank you for voting!