11072514101 Kenmore Dryer - Instructions

All Instructions for the 11072514101
121 - 135 of 1416

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud Noise While Drying
7 of 9 people found this instruction helpful.
  • John from Metamora, OH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Followed simple instructions to replace two pulleys and belt. The Virtual Repairman helped me identify the cause in minutes. Took another 5 minutes to place the order and the part arrived two days later. Saved $125 at least. Thank you!

john
Was this helpful?
Thank you for voting!
Dryer stopped spinning.
8 of 12 people found this instruction helpful.
  • sherif from BARTONSVILLE, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
Followed the PartSelect instruction video.
Basically opened the dryer.
Took the drum out.
Took the broken motor out.
cleanned the dryer since I had everything opened.
Replaced motor, pulley, old belt.
My 20 years old dryer is running like brand new.
Was this helpful?
Thank you for voting!
Needed to repair and replace dryer motor pulley and pully
6 of 6 people found this instruction helpful.
  • Rob from GAITHERSBURG, MD
  • Really Easy
  • 30 - 60 mins
  • Wrench (Adjustable)
this was very was very easy. But I deviated from the You Tube instructions. One to release the motor pulley. I needed to use 2 adjustable wrenches for a longer lever. I needed to use a hammer to help release pulley. Second to remove the dryer cable I needed to use a small screw driver to aid in the release. ---- the part from the comp any was a perfect fit.
Was this helpful?
Thank you for voting!
broken rib belt
6 of 6 people found this instruction helpful.
  • Robert from PEABODY, MA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Followed instructions from video, just removed lint collector, dryer top and front panel, removed broken belt and old idler pulley. Vacuumed and cleaned up inside dryer.installed new pulley and rib belt according to printed instructions,installed new dryer duct and new clamps. Saved myself huge service call or having to buy new dryer.Wil l be checking with this site on any future repairs instead of calling a repair service. Your video made it real easy to repair.and I am 77 years old.. Bob
Was this helpful?
Thank you for voting!
drum stopped rotating - broken belt
7 of 10 people found this instruction helpful.
  • lisa from manteca, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Super easy to repair...I had to idea how to get started; but after watching the video from your site it was a breeze. Thanks for having "how to repair" videos on your site.

Repair kit came in 2 days..fantastic..thank you so much....with new rollers, belt and tension roller she works like new
Was this helpful?
Thank you for voting!
Dryer would not start.
7 of 10 people found this instruction helpful.
  • Rebecca from Scarsdale, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!
Was this helpful?
Thank you for voting!
Loud, low-pitched thumping noise
7 of 10 people found this instruction helpful.
  • Joseph from SKANEATELES, NY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
First, let me say the t videos are excellent. Check them out if you haven't already.

I came across the video on diagnosing the causes of odd dryer noises. After watching that, I decided that the issue was probably a drum roller.

I took a chance and ordered the maintenance kit to avoid having to take the dryer part to confirm the diagnosis and then put it back together again while waiting for the parts to arrive (BTW - the parts arrived within two days of my ordering them) .

Even if you know your issue is only the roller, I recommend getting the entire kit. It takes no extra time to replace the drive belt and the idler pulley while you have to dryer apart and I consider it good preventative maintenance.

Definitely watch the how-to video PartSelect provides on how to perform the repair using the maintenance kit. It's very clear and very helpful. I'm not sure I could have figured out how the belt fit through the idler pulley without it.

As video shows, the repair is pretty straightforward. As others have noted, you'll likely find a couple of dollars in change and a goodly layer of lint in the bottom of the cabinet. Have your shop back handy.

It seems kind of silly, but I found the hardest part of the whole repair was getting the front panel to slide onto the two bottom clips that support it.

One thing to watch out for are two small metal clips surrounding the screw holes at the top of the front panel. The nut screws that hold the panel in place screw into these, not the panel itself. After I struggled to get the panel in place I realized that in the process I had knocked the clips off and so had to remove the front panel again in order to retrieve the clips from the bottom of the cabinet. Minor frustration. And with all the practice I had the first time around, the panel went on much more easily the second time :-)

It was very gratifying to plug the dryer in, turn it on and have it run perfectly. Better yet, it impressed my wife.
Was this helpful?
Thank you for voting!
flame fadedout after unit got hot; problem turned out to be the solenoid coils
6 of 7 people found this instruction helpful.
  • David from Adkins, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
removed frt & rear panels & drum and lint chute for seal replacement replaced these components, problem didn't go away, ordered & replaced both gas valve coils (m series coil kit) problem solved
Was this helpful?
Thank you for voting!
Dryer making a rumbling sound
8 of 13 people found this instruction helpful.
  • Michael from Jacksonville, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Purchased the dryer maintenqance repair kit. Very simple to do. Easy to follow instructions. Took less than an hour. Everything I needed was in th kit. Did not have to run to home depot for anything.
Was this helpful?
Thank you for voting!
Dryer got hot then heat would shut off
6 of 7 people found this instruction helpful.
  • Douglas from Fernley, NV
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and r everse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.
Was this helpful?
Thank you for voting!
Dryer on/off door switch broke and needed replaced.
8 of 13 people found this instruction helpful.
  • David from Fort Myers, FL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Took the dryer top off and removed the bad part. Looked it up online and found a replacement by looking for whirlpool parts. They didn't have one at the local parts stores so I ordered the part online and had it mailed within three days. I replaced it quite easily. It worked and I put everything back together and my wife took over the tricky part of drying the laundry! The repair was quite easy for a non mechanical person like me.
Was this helpful?
Thank you for voting!
Start windings burnt out on original motor (dryer would not start)
7 of 10 people found this instruction helpful.
  • Frank from Smyrna, TN
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to un thread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.
Was this helpful?
Thank you for voting!
Dryer would not stop. Heating problem also fixed
7 of 11 people found this instruction helpful.
  • Frank from Wingdale, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Followed the video .... Also installed another part. which was a kit. the video here showed the third wire being installed. The video on repair clinic did not show where to attach the third wire (orange wire). The Kit and the Thermostat was installed with 25 mins. Thanks
Was this helpful?
Thank you for voting!
The landry would not dry all the way at the end of the cycle.
8 of 14 people found this instruction helpful.
  • Mark from Houston, TX
  • Easy
  • 30 - 60 mins
First i removed the rear panel on the dryer.the removed bothe thermostats that were on the blower housings.unpluged all wiers and installed new thermostats.reinstalled the wiers in there proper locations...note to log the location of the wires when removing from old switch.reinstalled the rear panel and hooked dryer back up and test.
Was this helpful?
Thank you for voting!
Motor was bad
5 of 5 people found this instruction helpful.
  • Michael from CLIFTON HTS, PA
  • Really Easy
  • 30 - 60 mins
I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part s o I can redo a testimonial here for you. 19 days and still waiting
Was this helpful?
Thank you for voting!
All Instructions for the 11072514101
121 - 135 of 1416