110723120 Kenmore Dishwasher - Instructions

I removed the inner nut holding the spray arm onto the pump. Turned the washer on it's back and removed the wire clip holding rear of the pump motor. Completely removed the pump housingand motor from the washer. Removed three(3) long screws holding the motor to the pump housing. Removed the dish from the housing and removed the old impeller and seals .
Cleaned the pump housing of calcium with lime-a-way. Reinstalled all new parts in reverse order as they order taken off. Cleaned inside of dishwasher with lime-a-away and general purpose cleaner. Reinstall pump housing and motor on washer in reverse order as they were taking off.
Reinstalled washer into cabinet and connected all hoses, drain lines and electrical wired. Turned washer on and watched it run throught a complete cycle. Worked just fine and no leaks. Parts were great.

Sincerely,
James

first i picked out the old seal, use a screwdriver to get it started. Then I pushed the new one in after cleaning the seal channel. I fixed it during a commercial while watching my favorite tv show.

I first removed the old part. when i removed the old part i could not get the conector piece off when i when to get a new one they told me i should replace the copper tubing with the more flexable tubing because the copper tubing can kink up and possibly break from the kinking. so i screwed the inlet valve on i put teflon tape on the all the threads of the conector piece screwed it into the new inlet valve with and adjustable wrench then i conected the new tubing, and tightend it down with the wrench i slowly turned the water back on to cheak for leaks. When i saw there were no leaks i turned the water on the rest of the way pushed the dishwasher back in and screwed it into place an i was done.

replaced the rack adjusters

Simply removed deflectors and gasket, replaced all , took all of 5 mins. workes great now.

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

Pulled off the old valve using a crescent wrench and screw driver. The replacement part was a 100% exact match. Slapped on the new valve and that baby was water tight. $50 on a new valve is a lot better than $500 for a new washer.

Partselect.com was so easy to use and find the right part. Way more helpful than whirlpool's site, but that's not surprising seeing as they have an "authorized repair technician" page.

Thanks Partselect.com!

i determined that the impeller was not free. ordered and installed an impeller kit which included a new bushing, which was the culprit. it was a fairly simple fix, needing only to remove the pump housing from the back of the motor. access to the impeller was by removing the screw-in, x shaped connection on the back side of the impeller housing. runs like new again. the fix was far less expensive than a new washer.

My husband did the repair. He sucked the water out with the wet/dry vac. Layed it over on the front and removed the pump motor and replaced it.

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door

when my package arived , I open the box and pop on my wheels, and all fixed in 60 sec. Thanks you saved me about 650.00 for a new Dishwasher. Thanks Melissa

remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.

Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.

Pulled off the bottom trim, slid the old panel off and put the new panel on. Then popped back on the bottom trim.