110709 Kenmore - Instructions

All Instructions for the 110709
91 - 105 of 695

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Start switch didn't work, dryer ran when door closed
12 of 15 people found this instruction helpful.
  • Robert from Corvallis, OR
  • Really Easy
  • 15 - 30 mins
  • Socket set
I removed 5 screws from the back of the top panel, removed the back panel, removed the start button from front of dryer, twisted the old start switch from the back, removed the two leads, reinstalled new part in reverse order. It was that simple! 15 minutes top. Dryer works fine. Gave me a chance to vacuum out all the dust bunnies and clean out the dryer vent pipe as well.
Thanks!
Was this helpful?
Thank you for voting!
When using the dryer the cycle would stop and display E1 as the reason
13 of 18 people found this instruction helpful.
  • Joyce from Holbrook, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.
Was this helpful?
Thank you for voting!
Timer would stop the dryer with in 1 minute after set
16 of 27 people found this instruction helpful.
  • Romeo from Holland, MI
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Opened the back cover. Unscrewed the timer replaced the wires connected on the old timer to the new timer. Screwed the new timer in place screwed the cover back on. Then placed the timer nob on the front.
Was this helpful?
Thank you for voting!
Would not start
12 of 15 people found this instruction helpful.
  • Drew from Alachua, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First I tried a new switch, This did not fix the problem. Then I replaced the Fuse in the back of the unit.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Dryer timer stopped working
13 of 18 people found this instruction helpful.
  • James from Park City, UT
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Unfortunately it is not easy to get to this part due to the fact the control panel is attached to the top of the dryer by both plastic clips and screws. I was able to bend the back down in the back to gain access to the two screws that held the dryer timer in place. This job is much easier if you have an assistant to hold the thin tin o r steel backing away from the control panel while reconnecting the wire sensors to the new timer. This is the second time I have used Parts Select they are excellent and their prices are very competitive. The part was identical to the broken part. I saved at least $100 by doing the job myself.
Was this helpful?
Thank you for voting!
Dryer motor would not run
14 of 22 people found this instruction helpful.
  • David from Berkeley Springs, WV
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The motor relay arrived the day after I ordered it, and i had not requested expedited shipment. Thanks for the quick delivery.
I say the repair was a bit difficult only because it was not obvious at all how to open up the control console, and the user's manual was completely silent on the subject of disassembly . I finally found that the retaining end caps simply snapped off. Once the console was open, I found that the DIY instructions were folded up inside the console. Replacing the part only took about ten minutes. Now that I know how to open the console, the whole repair could be done in less than fifteen minutes.
Was this helpful?
Thank you for voting!
Idler pulley wore out
10 of 11 people found this instruction helpful.
  • Peter from HUEYTOWN, AL
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.
Was this helpful?
Thank you for voting!
Washer stopped working mid cycle restarts after resetting lid
12 of 17 people found this instruction helpful.
  • Eric from West Chester, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.
Was this helpful?
Thank you for voting!
Dryer would not start
11 of 14 people found this instruction helpful.
  • Daniel from Humboldt, KS
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Dryer would not start when the start switch was pushed. I was advised by the local repair shop to replace the "push to start switch" and the "thermal fuze". I unplugged the dryer and removed the back dryer casing which took all of 3 minutes. I removed the start switch and thermal fuze using directions on the whirlpool parts forum. This t ook maybe 5 minutes. I replaced with the new parts and put the casing back on the dryer. The entire project took 15 minutes. The dryer works perfectly. 34 USD for parts and shipping instead of 600 for a new dryer. Easy to identify the parts needed using the model number and the parts arrived the next morning I will use this company again for sure!
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people found this instruction helpful.
  • Dawn from Chesapeake City, MD
  • Really Easy
  • Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people found this instruction helpful.
  • stephen from langley, KY
  • Really Easy
  • Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
Gas Dryer would heat for one heating cycle but no gas afterward. Ignitor would glow.
10 of 12 people found this instruction helpful.
  • Jim from Foothill Ranch, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Checked four thermocouples all showed continuity with my multimeter so they were all good. I'd read that the coils commonly went out and that these were the symptoms. Hey, it's very simple in there. Not much else could be wrong. I had a Maytag repairman come out. At first he said the problem was a blocked vent. I knew he was wrong. Then h e said one of the thermocouples went out. It was $80 for him to come out. It turned out that his second diagnosis was wrong too. To repair the dryer by Maytag would have cost me $240. I gave him $80 and bought the coils for $37. They are EXTREMELY easy to replace: two screws held a bracket that held two coils. With the bracket off, I took off the old coils and slid on the new ones.
Was this helpful?
Thank you for voting!
Dryer squeeching very loud
9 of 9 people found this instruction helpful.
  • Michael from ENOLA, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Was this helpful?
Thank you for voting!
LP gas conversion
11 of 15 people found this instruction helpful.
  • Robert from Palmdale, CA
  • Easy
  • 30 - 60 mins
  • Socket set
Followed instructions, except to advoid sharp edges, and completed the job in under an hour.
Was this helpful?
Thank you for voting!
All Instructions for the 110709
91 - 105 of 695