1107010 Kenmore Dryer - Instructions

All Instructions for the 1107010
91 - 105 of 1694

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud banging noise when running dryer
15 of 18 people found this instruction helpful.
  • Joseph from Prospect Park, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Found one of the two drum support rollers was badly worn. Found Partselect.com, found my parts in less then 2 mins. Figured that I was in there so I should just replace the belt so I got one of those also. Parts arrived in 3 days dryer as good as new in 20 mins.
Was this helpful?
Thank you for voting!
Time clock not moving .Not enough heat
16 of 21 people found this instruction helpful.
  • PHILIP from LONG ISLAND CITY, NY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Was this helpful?
Thank you for voting!
Drum not turning; accompanied by loud "screeching" sound.
15 of 19 people found this instruction helpful.
  • holly from LONG BCH TWP, NJ
  • Easy
  • 30 - 60 mins
  • Socket set, Wrench (Adjustable)
Followed instructional video provided for this type of repair after diagnosing problem via of 'troubleshooting' on PartsSelect site. Simple, safe, and relatively easy (minimal mechanical knowledge helpful).
Second time using PartSelect; washing machine repair ~ 6 mo. previous.
PartSelect was spot-on with that repair as well, sa ving hundreds of dollars.....my go-to site for appliance repairs and pats....make it yours as well and you will NOT be disappointed! Fast, prompt shipping.
Was this helpful?
Thank you for voting!
Dryer would leave clothes damp
15 of 20 people found this instruction helpful.
  • Luke from Elmira, NY
  • Easy
  • Less than 15 mins
  • Nutdriver
First, I unplugged the dyer and then I removed all of the screws for the panel that covers the rear of the dryer. This exposed the cycling thermostat's location. I then removed the wires, one at a time so I would be able to put them back on in the same place. Then I removed the one screw using a nut driver and then put the new cycling the rmostat in place. It was pretty easy.
Was this helpful?
Thank you for voting!
The dryer suddenly started running cold - it would turn, the timer worked...but no heat. My wife mentioned that it had been taking longer and longer to dry a load of clothes....
12 of 12 people found this instruction helpful.
  • Geoff from Farmington, CT
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Popped the lower cover off the dryer, found the thermal fuse and thermostat mounted on the heating tube. Removed the screws with a nutdriver, swapped wires to the new parts, and reinstalled. Then I spent 30 minutes vacuuming 13 years worth of lint and crud out of the machine - it was pretty gummed up in spots, which is probably the cause of the failure.
I have a 25 foot run of hose from the dryer outside, so I replaced that with 4" metal ducting. Clothes dry much faster now!!! Maybe my electric bill will go down (fat chance :) )
Was this helpful?
Thank you for voting!
Burner would not go on on my Stack Set Dryer
16 of 24 people found this instruction helpful.
  • Robert from North East, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!
Was this helpful?
Thank you for voting!
drum very loud when rotating
13 of 15 people found this instruction helpful.
  • michael from indianapolis, IN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and repl aced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.

Thanks Mike
Was this helpful?
Thank you for voting!
No Heat
18 of 31 people found this instruction helpful.
  • stacy m from akron, OH
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
First time ever repaired anything let alone a dryer, I watch the video and followed instructions, was pretty simple, Works like a charm
Was this helpful?
Thank you for voting!
the drum was not turning because a broken belt
14 of 19 people found this instruction helpful.
  • thomas from bloomfield, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers
I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum expo sed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.
Was this helpful?
Thank you for voting!
Quick and simple - quickest $100 I've ever saved!
13 of 16 people found this instruction helpful.
  • Kelly from Waukegan, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
Removed the two screws under the lint trap
Opened the top (had to use flathead screwdriver to release latches)
Disconnected door switch harness from front panel
Removed 2 screws holding front panel on dryer
Lifted out dryer drum (previous belt had broken)
Vacuumed inside of dryer (found $3 in quarters!)
Put n ew belt around drum
Put drum back in dryer, using empty laundry soap bottle to support its weight
Looped belt around pulley and motor; secured pulley to dryer bottom
Made sure rear gasket thingy was aligned properly and drum turned freely
Put front panel back on
Re-attached door switch
Closed top and put screws back in under lint trap
Fired it up - WOOHOO!
Was this helpful?
Thank you for voting!
dryer not heating up
12 of 14 people found this instruction helpful.
  • Richard from New Windsor, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helpi ng me out!!!
Was this helpful?
Thank you for voting!
The dryer was not fully drying
12 of 14 people found this instruction helpful.
  • Michael from Chicago, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.
Was this helpful?
Thank you for voting!
The Dryer would not get hot.
14 of 20 people found this instruction helpful.
  • Jerry from Bradenton, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.
Was this helpful?
Thank you for voting!
Aft seal deterioated and causing brown spot on clothing due to netal to metal contact.
11 of 12 people found this instruction helpful.
  • Cleo from Laurinburg, NC
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Removed top and front of dryer then drum and followed the instructions in the package. It was a real simple procedure. I did additional cleaning while the dryer was disassembled.
Was this helpful?
Thank you for voting!
Motor wore out
12 of 15 people found this instruction helpful.
  • Charles from Clarissa, MN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I took the dryer apart ( using a repair book ) It was Super Simple to do I only needed a extra set of hand's to hold the drum in place while reassembling it. removed the hold down snap on collar's on the Motor ( after removing the Blower from the back of the dryer ( super simple. Extra set of hand's needed ) Reassembled in the same order. And now The Dryer work's like NEW..Shure Beat Buying a new Dryer..
Was this helpful?
Thank you for voting!
All Instructions for the 1107010
91 - 105 of 1694