- Home
- 11070022011
- Instructions
11070022011 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
lint screen damaged . Orordered part but did not receive it. Instead received various parts to repair clothe washer.
3 of 4 people
found this instruction helpful.
-
Marsha from SEARCY, AR
- Very Difficult
- Less than 15 mins
Item not repaired as did not receive my order. I did call the company and they said they would credit my card. Neither they nor the company the wrong order came from seemed interested in my efforts to return the wrong order. I feel this incredibly wasteful,. I would not order from a company with this attitude
Was this helpful?
Thank you for voting!
handle on old dryer screen had broken off
2 of 2 people
found this instruction helpful.
-
Bernette from LONG BEACH, CA
- Very Easy
- Less than 15 mins
Removed old screen. Placed in new screen.
Was this helpful?
Thank you for voting!
Side of lint filter (screen) cracked and broke off.
2 of 2 people
found this instruction helpful.
-
Charles from Seneca, PA
- Really Easy
- 30 - 60 mins
Pulled the old lint filter out and threw it in the trash. Slid the new filter in and it was all done. Doesn't take a genius to do this repair. My old dryer a sears/kenmore is over 40 years old and the lint filter fit perfect. (MF part number w10874409)
Was this helpful?
Thank you for voting!
broken
2 of 3 people
found this instruction helpful.
-
Marianne from OCALA, FL
- Very Easy
- Less than 15 mins
It fit like a glove. Just put it right in.
Was this helpful?
Thank you for voting!
replace the lint filter
-
James from Bronx, NY
- Really Easy
- Less than 15 mins
took out the old filter and put in the new lint filter...it was a snug fit.
Was this helpful?
Thank you for voting!
Starter would not stay on after pushing on
-
Rosemary from Ellicott City, MD
- Really Easy
- Less than 15 mins
-
Screw drivers
Followed video, very easy installation. Unfortunately, the new starter switch does not stay on either so we still have not resolved the problem.
Was this helpful?
Thank you for voting!
the drter would not start
-
linda from South Lebanon, OH
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
since dryers are hard for me to determine. I used my OHMs meter to see that the Thermal Fuse was good. The door switch was good . The off on switch was bad.
Was this helpful?
Thank you for voting!
clothes dryer wouldn't continue to run after push-to-start switch was released
-
Mo from Portland, OR
- Really Easy
- 30 - 60 mins
-
Screw drivers
Unplugged dryer. Removed control panel end caps, removed anchor screw at each end of control panel that had been covered by end cap. Tilted control panel up to access components on back side. Using tech sheet found inside contol panel, swapped motor relay with heater relay (they're identical). Plugged dryer back in, pushed start switch
... Read more
; dryer continued to run (problem identified). Unplugged dryer; replaced relays to original positions. Ordered new power relay (p/n 3405281). Installed new relay when it arrived, plugged dryer in, tested it. Dryer worked normally (problem fixed). Unplugged dryer, reinstalled control panel anchor screws and end caps. Plugged dryer back in. Dryer continues to work normally.
Read less
Was this helpful?
Thank you for voting!
The lint screen was broken
-
Melanie from Staples, MN
- Very Difficult
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
I ordered a new lint screen to replace the old. I used the part #. They only had "similar" products, not one exactly like mine. When the new part arrived, I had to take IT apart and use part of the new with part of the old, to get a working lint screen. I was able to do it only because of my internal sense of mechanics...and I am prou
... Read more
d to say I am a woman!
Read less
Was this helpful?
Thank you for voting!
on-off switch
-
vincent from lesterville, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver
took off the back part with nut driver removed switch assembly by pressing down with a little pressure and it snapped out the new was a little different but worked on installing this was an easy assembly. just do things in reverse when finished just plug in electric and push switch to turn on. very easy to install.
Other Parts Used:
Was this helpful?
Thank you for voting!
push to start switch didnt work
-
LEE from BUTLER, TN
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed access panel installed new switch reinstalled access panel
Was this helpful?
Thank you for voting!