110698 Kenmore Dryer - Instructions

First, I replaced the heating element which was super easy but I still didn't have heat - frustrating! I then ordered the thermal cut-off kit and thermal fuse. I replaced the thermal fuse and still no heat. Then, I took one of the fuses from the kit and replaced that and finally got heat. There was another fuse in this kit that I still do ... Read more n't know where it goes but right now I don't need it. Had I known (by a volt tester) this would have been super easy to fix, but I didn't have one so it was trial and error. I did find out, however, that if the heating element goes it usually takes the fuse with it. The fuse I replaced (that finally gave me heat) was located in the casing just above the element. I hope this helps!

1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall ... Read more when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)

After realizing that my dryer was no longer heating, I took off the back and examined the heating element. I saw that a coil was broken and knew that it needed replaced. When the part came in, I basically changed out the wires that were plugged into the old element on to the new one, replaced the screws in the heating element housing an ... Read more d back panel, plugged in the dryer and was back in business! Oh, by the way...I am a 49 year old WOMAN!!!!

First unplug your dryer. Then, I removed the two screws on the lint trap leaving the lint trap in place--do not pull out the lint trap--only remove the two screws. Next, slide the top of the dryer slightly forward in order to release the top of the dryer. I did this with my hands. Once the top of the dryer is released, raise the top of t ... Read more he dryer and unplug the door switch assembly. Then, remove the two screws that hold the switch. These two screws were located on the front panel of my dryer and are visible when you open the dryer door. Remove the old switch and install the new switch by putting the two screws you previously took out from the old switch back in place and plug in the new switch. Lower the dryer top. Push the top back to lock in place. Line up the lint trap holes for the two screws that hold it in place and replace those screws. Plug your dryer back in and it should work properly. Very easy repair. We ordered our part one morning before noon, and it was here the next afternoon with regular shipping. GREAT SERVICE.

I Looked on internet sites for this type of problem.
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I h ... Read more ad also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.

Edward Brennan

Turned off the power.Pulled the dryer out, removed the screws from the control cover panel, unplugged the switch, pressed the release clip the did the opposite to install new switch. Replaced the back panel, put the nob on and it looks as good as new.Turned on the power.

This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door ... Read more was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.

After looking on the website for advice I walked throught the simple steps of disassembling the front, removing the drum, removed the back, disconnected the wire harness. Then removed the blower housing in the back. The blower, mounted on the back side of the motor was very tight. I used a pipe wrench wedged in place and help by my 10 ... Read more year old Grand-daughter while I used an adjustable wrench to turn the shaft on the front of the motor. Spun the blower off, removed the two clips holding the motor. Then reversed the process when I received the new motor. Care should be taken to avoid damaging the blower fan if a lot of pressure is required.

couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! ... Read more Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!

Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcer ... Read more ting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.

Removed rear panel 10 screws, and heating element was situated on the right hand side of dryer and was held in place by two screws and had two heavy duty red wires connected to the element which were easily removed . Installing this item was a breeze .

1) Disconnected power cord from wall. 2) Disconnected vent hose from back of dryer. 3)Removed dryer rear panel. 4)Disengaged tension spring on idle wheel arm. 5) Removed worn idle wheel. 6)Installed new Idler wheel assembly. 7) Vacuumed dust from rear of dryer (optional, recommended). 8) Reinstalled rear cover, vent hose and power cord. E ... Read more asy repair 15-30

I read a fix-it article from another contributor and followed those instructions to the T. Pull out lint trap, remove the two screws. Slide the top cover towards the front and prop it up with a mop handle.
Unscrew two screws in the door switch (with the door open) - Oh, to keep from killing yourself unplug the dryer just in case. ... Read more Take pliers and pull the plug apart. It will be right in front of you in the right corner at the top. Plug new switch into that plug, reinstall the switch by reinstalling the two screws you removed. Snap top back into place and reinstall the two screws at the lint trap. Oh, don't forget to clean the trap and slide it back into the unit. Now you have earned that beer.
Put tools away and proudly show your job off to the wife telling her how difficult it was.

I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks

First I removed back and top of dryer, then the support braces holding the drum, after that I took the drum out and the blower covers and cleaned the whole dryer of lint and other debris. Installed the new belt and then reassembled the dryer.