110694670 Kenmore Dryer - Instructions

removed the two screws that hold the coils in place pulled the coils terminal connections off removed and replaced with new coils reattached quick disconnect terminals dryer now works better than when it was new

First we removed the front panel then the door. Removed the old coils and put in the new coils, oh yeah don't forget to disconnect the power supply first. Sure enough that was all it took and it runs great. You really can fix your own appliance if you take the time to do some research.

I shut off the power supply (pulled plug) . Opened the front access door on bottom of dryer, The two coils sat on top of burner unit, with a plate and 2 Phillip head screws securing them. .I used a small set of pliers to pull the terminals off, then I used a short Phillip head screw driver due to the proximity of the dryer drum close by. The coils slide off, slide the new ones on, re secure the plate with screws, reconnect the terminals, plug in the power cord and away you are for a fraction of the cost.

Installed new coil, helped but have other issues that I'm troubleshooting.

replace two heating coils. Dryer working find.

I watched a video. The man speaking was Wayne from parts direct. He made the repair go so smoothly. I enjoyed watching him and I hope you include him in more videos. Had dryer apart and back together (after I had to take top back off, to re-attach the door switch, which I forgot. Had a senior moment!!) in 15 min.And working as good as new. Thank you Wayne. Have a nice day. Bryan

I used a socket to take of the front cover. I used a screwdriver to remove the two screws that held the coils in place. Replaced the coils and put everything backs together. Piece of cake!

Well, this is quite easy really. I found the problem after plucking and chucking a few parts but it was finally the igniter that was the problem. After taking the front section panel off to access the components, take the time to unscrew the igniter and see if it is cracked. That is what happened to my unit. I replaced to the new M series coils as well but the issue was the igniter. Look very carefully for a crack, the one on my unit was very small. You can ohm it out with a meter and if it reads open it is cracked.

Checked ignitor it was working ok, disconnected 3 pronged coil and disconnected 2 pronged coil using multi tester checked continuity on both coils both tested 0,with help of operator ordered M Series new style coil kit. When parts arrived installed coils attached wire harnesses installed bracket and 2 screws that secures coils. Started dryer it worked and stayed working who needs the Maytag Repair Man probably saved about 200.00 between service call and markup on coils. Thanks Virtual Repairman

1. Unplugged from wall, turned off gas and opened top cover. 2. Removed two wire clips for door switch and unscrewed front cover (2 screws inside). 3. Removed front cover and moved to side. 4. Unplugged connectors from coils. 5. Unscrewed coil screws. 6. Replaced coils and tightened screws. 7. Replaced front cover, tightened screws and reinstalled wire clips. 8. Closed top cover, turned on gas and plugged in power. 9. Dryer fired right up and made heat.

The front panel was taken out and the parts were replaced. After the replacement, the drying time went back to the original 30-40 minutes.

Gas valve coils need replacing I followed parts select.com video on YouTube and had no problem. It went exactly as the video followed parts select.com video on YouTube and had no problem. It went exactly as the videos showed!

Unplug from electricity, turn off gas valve, raise top, remove front. Take drum out of cabinet, unhook gas line from burner assy. unhook electric wires, marking them for re installation. Remove, and replace burner tube. Reinstall burner assy attach wires and gas line. (Check for leaks) Reassemble drum to cabinet, rethread belt thru tensioner, reinstall front, let top back down on unit.

bought the new coil valves changed out new for old, presto dryer works now

This 10 year old dryer stopped heating. I knew a Maytag would have much more life left in it than that (even my Mom's lowly GE lasted more than 40 years!) so I was sure it could be fixed. Without doing any testing, I had just guessed that the glow bar was bad and replaced it. But that wasn't the problem - the old glow bar still had continuity as tested with my ohmmeter. So I dug in deeper and looked over the schematic posted on PartSelect's website. The glow bar would light up and then go out, but the gas valve never opened. After probing the two solenoid coils for voltage, I decided the primary solenoid was bad. This was confirmed when I took the connector off and checked with an ohmmeter (never do this with the wires connected!) and found no connection at all between the two terminals.
Ordering the new part from PartSelect was fast and easy and my part arrived in two days. The solenoid coil on this dryer can be removed from the gas valve without taking any gas lines apart - I don't know if they're all like that, but it's a great feature. The only hard thing is that there is no access door to inspect the flame like older gas dryers. You have to take the front panel off to watch it working, but that just involves the four screws around the door opening.
If your pre-Whirlpool Maytag dryer is giving you trouble, take heart! These are great machines that last long, are easy to fix, and parts are easier than ever to get with PartSelect!