110694 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door Gasket tore out
17 of 17 people
found this instruction helpful.
-
Manolak from MURFREESBORO, TN
- Easy
- Less than 15 mins
Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine....
Was this helpful?
Thank you for voting!
Drum was binding because of worn bearing supporting front of dryer drum
23 of 35 people
found this instruction helpful.
-
Leslie from Townsend, GA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to gl
... Read more
ue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!!
Read less
Was this helpful?
Thank you for voting!
No heat in dryer
18 of 21 people
found this instruction helpful.
-
Kenneth from Durham, NC
- Easy
- 15 - 30 mins
-
Nutdriver
Once I unpluged the dryer and then removed the back cover, I located the heating unit and then removed the thermostat. Once that was done, I installed the new thermostat and connected the wires. I tested the dryer to make sure that it would heat. Then I replaced the back cover.
Was this helpful?
Thank you for voting!
dryer sounded like I was strangling a dog
18 of 21 people
found this instruction helpful.
-
Lynda from Syracuse, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First, I watched a utube video of replacing the dryer belt. Then I went to Sears Hardware and couldn't find a part. Then I ordered the parts for my favorite online repair parts source - partselect.com. I had the part in one day! We did exactly what the video showed and also replaced the two wheels that looked like roller blade wheels. Pie
... Read more
ce of cake. Saved a $75 repair call plus whatever the parts would have been and spent about 20 minutes doing it. Back in business. Great for a 12 year old dryer! Buy the dryer kit!
Read less
Was this helpful?
Thank you for voting!
Broken push to stat switch
18 of 21 people
found this instruction helpful.
-
Charles from Fairfax, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed back cover, removed broken switch, replaced with new switch, replaced back cover, told wife her dryer was fixed.
Was this helpful?
Thank you for voting!
dryer not working
22 of 33 people
found this instruction helpful.
-
Maura from Newtown, CT
- Really Easy
- Less than 15 mins
After unplugging and removing the back cover from the dryer, locate the push button switch. Slide putty knife around outer cover to unhook catch. Replace with new push button switch. My dryer is still not working, but this was a simple replacement.
Was this helpful?
Thank you for voting!
Squeaky Dryer
17 of 19 people
found this instruction helpful.
-
Daniel from Hamilton, OH
- Easy
- 15 - 30 mins
-
Screw drivers
I looked for squeaky dryer within parts select and went with the 80%. I received the Maintenance Kit, replaced two rollers and it works like new. Amazing since this is the first time I have ever opened a dryer. The instruction sheet and parts were all I needed.
Was this helpful?
Thank you for voting!
Loudly clunking clothes drum due to worn out roller
17 of 20 people
found this instruction helpful.
-
KENNETH from WEST ORANGE, NJ
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Followed video on Parts Select site for comparable model showing roller and drive belt replacement.
The triangle plastic retaining clips were the most difficult part , to put
on and take off. They required careful , firm stretching with needle nose pliers.
The triangle plastic retaining clips were the most difficult part , to put
on and take off. They required careful , firm stretching with needle nose pliers.
Other Parts Used:
Was this helpful?
Thank you for voting!
Getting to hot and shutting off after 20 minutes
16 of 18 people
found this instruction helpful.
-
William from `Omak, WA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I watched the installation video on both parts before I purchased them and it was a piece-of-cake after that.
Other Parts Used:
Was this helpful?
Thank you for voting!
Drum spinning but no heat
19 of 27 people
found this instruction helpful.
-
Chad from Derby, KS
- Easy
- 15 - 30 mins
-
Socket set
Purchased thermal cut off kit but only replaced the top most thermostat. There were some extra wires wired into the bottom thermostat, that were not described on the video or any other repair user posts. It checked fine on my multimeter anyway.
Was this helpful?
Thank you for voting!
Rear Drum Seal started to come apart
16 of 18 people
found this instruction helpful.
-
Brett from CRESCENT CITY, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Used the YouTube video sent by this site
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer kept spinning when the door opened
16 of 18 people
found this instruction helpful.
-
Gary from Ocean Springs, MS
- Really Easy
- Less than 15 mins
-
Screw drivers
Came to Parts Select. Looked for door switch. Read what other people did. Part came in a few days took a few minutes to take old switch out (had to pry the plastic connection apart with little thin screwdriver). Everything was easy
Was this helpful?
Thank you for voting!
Lint screen torn
15 of 16 people
found this instruction helpful.
-
James from Glenside, PA
- Really Easy
- Less than 15 mins
Lint screen on my 30-year dryer was torn. Ordered the new screen here with just the part number, fits well. Very helpful website.
Was this helpful?
Thank you for voting!
Change dryer belt
15 of 17 people
found this instruction helpful.
-
Scott from Bayport, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I p
... Read more
opped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.
Read less
Was this helpful?
Thank you for voting!
Door catch on dryer door broke
14 of 14 people
found this instruction helpful.
-
Lynne from Jamestown, CA
- Really Easy
- Less than 15 mins
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might c
... Read more
ontact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.
Read less
Was this helpful?
Thank you for voting!