110692 Kenmore Dryer - Instructions

All Instructions for the 110692
76 - 90 of 2021

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Heat, no ignition in burner
21 of 26 people found this instruction helpful.
  • Russell from Santa Maria, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
Our dryer would not heat and it seemed that no gas was coming from the regulator. The igniter was working fine but the burner never turned on. To check the problem, i followed the instructions to remove all body panels until I had access to the burner assembly. I dismantled both gas valve coils and tested each one for open or closed circu it using my multi-tester. I found that the three terminal gas valve coil was an open circuit and was not functioning so I ordered a new one from PartSelect and within just a couple days, had the drier back up and functioning. I also replaced the igniter due to a malfunctioning igniter that has been changed by the manufacture. I must say that PartSelect has the fastest shipping I have ever seen. One part I ordered was at my door in less than 24 hours and I only paid standard shipping...un real! OUTSTANDING....5 STAR SERVICE
Was this helpful?
Thank you for voting!
Replaced belt while I was in there replacing motor
20 of 24 people found this instruction helpful.
  • Douglas from COMMERCE, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
If you were to do the Belt Replacement only, here is the quick synopsis:
1. Unplug dryer;
2a. Open lint door on top of dryer and remove the two phillips head screws that hold the lint bay to the metal dryer top;
2b. Next remove the two brakets holding the metal top to the dryer back (one screw on each bracket);
3. Use a flat-blade screw driver to pry off the top of the dryer (leaving the timer and start button area attached);
4. Lift off top and push back to expose just enough area so you can get to the two screws holding the dryer sides to the dryer front;
5. Unplug door switch;
6. Unscrew screws from #4;
7. With door open, lift dryer front (only about an inch) and then pry bottom of dryer front from dryer sides. The bottom of the dryer front is not screwed, just siting on Front Panel Clips;
8. Once the front is off the dryer, simply remove the belt and install the new one. Please note that while you are in here, you may want to inspect the rear drum seal and replace if it is worn to the point where metal is rubbing on metal. This is also a good time to clean out dust from inside this cavity to help extend the life of the bearings on the rollers and prevent dust from accumulating and gunking up the motor, etc.
9. Re-assemble tin the opposite order.
If you have any mechanical sense at all and you don't know anything about dryers, you will be surprised at the simplicity of the dryer.
Was this helpful?
Thank you for voting!
How to un-screw the blower fan!
19 of 21 people found this instruction helpful.
  • Tim from Fremont, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
The dryer motor quit working. Learned, if you are changing one that is old, get the blower wheel fan too! I could not break mine loose from the motor shaft, and had to bust it off.

To un-screw the blower wheel fan from the motor shaft: from the front of the dryer, grab the plastic fan on the back of the motor with an adjusta ble wrench, and the motor shaft on the front of the motor with vice grips. Turn the motor shaft CLOCKWISE holding the fan still to un-screw the fan. If you have to remove the pulley, grab the shaft and turn the pulley COUNTERCLOCKWISE with a wrench.

Just make sure to pay attention to the orientation of the new motor in the instructions. If you match the old motor, it will not fit. It is all spelled out in the directions.
Was this helpful?
Thank you for voting!
Heat Would Not Come On
20 of 24 people found this instruction helpful.
  • Lynn from Novi, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.

After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lo t of time and money if I had read that earlier.
Was this helpful?
Thank you for voting!
Would not start
20 of 24 people found this instruction helpful.
  • Mark Lariviere from NY, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
We were able to look at the diagram of the dryer to figure out how to access the part and then replace it. Fantastic! Your site is wonderful. The suggestion for the repair for not starting was right on the mark. The parts came very quickly, as well.
Was this helpful?
Thank you for voting!
Motor would not turn
21 of 28 people found this instruction helpful.
  • Christopher from bellerose, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
1) Removed top of dryer
2) removed belt and drum
3) removed front of dryer
4) popped clips holding down motor
5) unscrewed rear fan from motor (by exposing and holding fan)
6) changed motor
7) changed support rollers and idler pully
8) reassemled dryer
Was this helpful?
Thank you for voting!
The Dryer was working normally, just no heat
19 of 22 people found this instruction helpful.
  • Andrew from Roslyn Heights, NY
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Very Very Easy all you need is a 1/4 inch nutdriver. 1st remove the screws from the back of the dryer. 2nd you will see a shaft like duct work. remove the 2 screws from this shaftway, lift out the old heating element and replace with the new element. Part select was right on target and fast. 2 days to recieve my order. I expected to hav e to buy a new appliance. Partselect made it possible to fix it like new for around $80.00
Was this helpful?
Thank you for voting!
Dryer would not heat
20 of 25 people found this instruction helpful.
  • Gary from Seguin, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
First I removed the two wires from the overheat fuse, then I removed the 1 screw and removed the fuse. I installed the new overheat fuse and attached with 1 screw, then reconnected the 2 wires. I attached the back cover with two screws and tested the dryer. It was working, so I finished attaching the back with the remaining screws and exhaust duct. Installation complete.
Note: Two weeks later I had to replace the fuse again because I had checked the duct pipe and exhaust chute, but not the bottom at the fan. Be sure to remove the flat exhaust duct and check for bulid-up at the bottom under the fan.
Was this helpful?
Thank you for voting!
dryer worked but no heat
18 of 20 people found this instruction helpful.
  • Tracie from Culver City, CA
  • A Bit Difficult
  • 15 - 30 mins
Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.
Was this helpful?
Thank you for voting!
Door Gasket tore out
17 of 17 people found this instruction helpful.
  • Manolak from MURFREESBORO, TN
  • Easy
  • Less than 15 mins
Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine....
Was this helpful?
Thank you for voting!
Drum was binding because of worn bearing supporting front of dryer drum
23 of 35 people found this instruction helpful.
  • Leslie from Townsend, GA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to gl ue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!!
Was this helpful?
Thank you for voting!
No heat in dryer
18 of 21 people found this instruction helpful.
  • Kenneth from Durham, NC
  • Easy
  • 15 - 30 mins
  • Nutdriver
Once I unpluged the dryer and then removed the back cover, I located the heating unit and then removed the thermostat. Once that was done, I installed the new thermostat and connected the wires. I tested the dryer to make sure that it would heat. Then I replaced the back cover.
Was this helpful?
Thank you for voting!
Getting to hot and shutting off after 20 minutes
16 of 18 people found this instruction helpful.
  • William from `Omak, WA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I watched the installation video on both parts before I purchased them and it was a piece-of-cake after that.
Was this helpful?
Thank you for voting!
Dryer kept spinning when the door opened
16 of 18 people found this instruction helpful.
  • Gary from Ocean Springs, MS
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Came to Parts Select. Looked for door switch. Read what other people did. Part came in a few days took a few minutes to take old switch out (had to pry the plastic connection apart with little thin screwdriver). Everything was easy
Was this helpful?
Thank you for voting!
Drum spinning but no heat
19 of 27 people found this instruction helpful.
  • Chad from Derby, KS
  • Easy
  • 15 - 30 mins
  • Socket set
Purchased thermal cut off kit but only replaced the top most thermostat. There were some extra wires wired into the bottom thermostat, that were not described on the video or any other repair user posts. It checked fine on my multimeter anyway.
Was this helpful?
Thank you for voting!
All Instructions for the 110692
76 - 90 of 2021