110689 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer wouldn't run
6 of 6 people
found this instruction helpful.
-
Edward from Richlands, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
Extremely easy repair! Unplug the dryer. Remove the lint trap screen. Take the two screws out of the lint trap chute, pry up the top of the dryer, insert wood or have someone hold top up, remove two screws holding the switch in place while holding the switch so the old spring doesn't fall. Remove old spring and replace with new one.
... Read more
Re-attach switch to dryer with two screws. Plug in and test run. Lower top and push firmly to engages clips. Re-install two scres in lint trap chute followed by the lint trap screen and you are finished!
Repair took about five minutes and saved approximately $70!
Repair took about five minutes and saved approximately $70!
Read less
Was this helpful?
Thank you for voting!
Dryer would start and then stop after a few minutes, eventually it completely stopped.
11 of 21 people
found this instruction helpful.
-
Keith L. from San Diego, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench (Adjustable)
After determining that the dryer motor was the issue, I wrote down the part number and logged on to partselect.com website.
I input the number into the search box and there was the exact motor I needed.
The correct part showed up in a timely manner and the pricing was very fair.
I disassembled the dryer, ... Read more removed the old motor and reinstalled the new motor within about 30 minutes.
Key point was to read the instructions first and then reconnect the wiring to the new motor. The new motor has the switch install in a different spot on the motor so be careful to follow the instructions but, the instructions were very clear and connections were very simple.
I also did some preventive maintenance while I was in the unit by cleaning out any remaining lint from the heater unit and surrounding areas, that took about 30 minutes. Reassembling was a snap and I turned on the gas, plugged it in and........SUCCESS! Total time of repair and cleaning was about an hour.
I had a load of laundry ready to go and put the new motor right to work. It has been non-stop drying and thanks to Part Select for getting everything right the first time. It has been a positive experience and I will tell others about the website if they have similar problems. Thanks again for a success story and dry clothing.
I input the number into the search box and there was the exact motor I needed.
The correct part showed up in a timely manner and the pricing was very fair.
I disassembled the dryer, ... Read more removed the old motor and reinstalled the new motor within about 30 minutes.
Key point was to read the instructions first and then reconnect the wiring to the new motor. The new motor has the switch install in a different spot on the motor so be careful to follow the instructions but, the instructions were very clear and connections were very simple.
I also did some preventive maintenance while I was in the unit by cleaning out any remaining lint from the heater unit and surrounding areas, that took about 30 minutes. Reassembling was a snap and I turned on the gas, plugged it in and........SUCCESS! Total time of repair and cleaning was about an hour.
I had a load of laundry ready to go and put the new motor right to work. It has been non-stop drying and thanks to Part Select for getting everything right the first time. It has been a positive experience and I will tell others about the website if they have similar problems. Thanks again for a success story and dry clothing.
Read less
Was this helpful?
Thank you for voting!
No Heat
7 of 9 people
found this instruction helpful.
-
Ken from Bixby, OK
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
Thermal fuse was blown so I replaced it. Still no heat. Hi-Limit thermostat and Cycling Thermo. had continuity as did flame sensor. Igniter tested 66ohms. I placed a wire jumper across the Hi-Limit and the igniter glowed, solenoids opened and gas came on. I orderd the Hi-Limit and since both "overheating" limiters were defective I de
... Read more
cided to order the cycling thermo just in case. The Hi-Limit was received in 2 days but the Cycling Thermo was backordered. In the meantime my wife got antsy so I went ahead and installed the Hi-Limit and put her back in service... ...for one load. I wasn't certain if I had fried the "limiters" again but since they had continuity and I could measure continuity all the way to the Igniter I decided that it HAD to be the cause. I ignored the flame sensor since it never came into play without the igniter glowing... The igniter arrived and measured 56ohms. Hmmm... After installing the problem was solved. Word of advice: If the thermal fuse is blown and even if all else in the circuit SEEMS ok, go ahead and order the Fuse, Hi-Limit and Cycling Thermos, and the Igniter. It will take you about 30 minutes to install and you'll reduce your out-of-service time! Good luck!
Read less
Was this helpful?
Thank you for voting!
Drive pulley broke. Looked like clip holding it on broke and pulley was running crooked.Belt was squealing some a couple of weeks before it broke.
6 of 7 people
found this instruction helpful.
-
Mark from Sheffield, PA
- Easy
- 30 - 60 mins
-
Socket set
Removed top and back covers. Placed new pulley and retaining clip in place. I had to remove a couple of drum supports to put belt on. Probably didn't have to remove top.
Other Parts Used:
Was this helpful?
Thank you for voting!
not heat
7 of 10 people
found this instruction helpful.
-
Sarah from Merrimac, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
For the Ignitor - As involved as taking the dryer completely apart sounded, it was super easy. 1-take out the lint trap and remove the two screws there. 2-Pop open the top with a screw driver and swing the top completely over/back. 3- remove the two screws holding in the front panel and remove the panel. 4- loosen the belt by pushing on t
... Read more
he tension roller under the drum on the right and remove the drum (its super light) use the belt as a handle. 5- remove the screw holding in the ignitor and replace it with the new one. Be careful to not touch the new ignitor. Then go backwards putting it back together.
Read less
Was this helpful?
Thank you for voting!
Dryer not Heating
6 of 7 people
found this instruction helpful.
-
Brigitte from Westerville, OH
- Easy
- 15 - 30 mins
-
Nutdriver
Was not sure what was wrong but the Part Select site allowed us to view other repair issues and solutions. We ordered the kit, it arrived the next day (how is that possible) and easily put the parts in and chaching...money saved and dryer works better than ever. THANKS PartSelect, we give you an eleven and we will recommend you to everyon
... Read more
e.
Read less
Was this helpful?
Thank you for voting!
The belt you sent was too short
6 of 7 people
found this instruction helpful.
-
Larry from Middlebury, IN
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I disassembled the dryer, replaced the pulley (which was noisy), and the belt.reassembled, only to find out that the drum would not turn freely. checked all my procedures and kept having the same problem. Finally after 3 frustrating hours, I took the back off and noticed that idler arm was tight against the motor shaft, because the too s
... Read more
hort belt didn't allow for the clearance needed. Had too take everything apart ,another hour, went and found one at our local repair shop, reinstalled everything , after another two hours runs fine. would appreciate a refund. And please check your part numbers in the future. Would hate to have someone else go through what i experienced.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken Motor Pulley
7 of 10 people
found this instruction helpful.
-
Mark from PELHAM, MA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Socket set
Removed back panel of the dryer-reached my hand to the back of the motor shaft, put 7/16 wrench on it to hold the shaft while I removed the broken pulley with pliers. Very easy fix-the tech on Utube took the entire dryer apart totally unnecessary. If that is what the factory tells its tech"s to do its no wonder why the labor charge woul
... Read more
d be thru the roof.
Read less
Was this helpful?
Thank you for voting!
Noisy
5 of 5 people
found this instruction helpful.
-
Robert from HAGERSTOWN, MD
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Disconnect power supply, remove power cord from dryer, remove dryer vent tube from dryer, remove 2 Philips screws from power connection on dryer, remove nuts from back of dryer, remove back of dryer. Locate idler pulley at bottom of unit at the rear of the motor, pull pulley back to loosen belt and remove from pulley, remove pulley retain
... Read more
er clip, remove pulley and rear washer from shaft and inspect shaft for wear or rust. replace washer and pulley (no specific direction to replace them, washer first then pulley). Reverse above procedure to reassemble. This is for a front load dryer, a top load dryer is different.
Read less
Was this helpful?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
6 of 8 people
found this instruction helpful.
-
Betty from Erie, PA
- Really Easy
- 15 - 30 mins
-
Socket set
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Was this helpful?
Thank you for voting!
Dryer was Noisy
6 of 8 people
found this instruction helpful.
-
Doug from HARRODSBURG, KY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I simply followed the video and apart from a couple of areas that were not relevant to my model, everything went exactly as illustrated. The video is excellent and made the repair so easy.
The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back ... Read more and two in the front.
A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.
It was an easy fix, I just did half the install a second time.
The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back ... Read more and two in the front.
A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.
It was an easy fix, I just did half the install a second time.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would not heat.
7 of 11 people
found this instruction helpful.
-
Russell from Orlando, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Watched on-line video on how to disassemble and test heater element, thermostat, and hi-temp shut down. Heater element was open. Ordered new heater element. Re-installed heater element iaw video provided with parts. Video provide was one of the best I've seen. Explanation on releasing access panel was especially helpful.
Other Parts Used:
Was this helpful?
Thank you for voting!
Lint filter seal worn out
5 of 5 people
found this instruction helpful.
-
Dennis from PALM BCH GDNS, FL
- Very Easy
- Less than 15 mins
The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.
Was this helpful?
Thank you for voting!
Dryer had no heat at all. This is an older gas dryer.
5 of 5 people
found this instruction helpful.
-
todd from MILFORD, PA
- Really Easy
- Less than 15 mins
-
Wrench set
Cleaned out years of fuzz behind lower access panel and noticed where the igniter sits there is a metal tube about 1 inch in diameter. It had rust on the end and was starting to flake away. Found some helpful hints about how to test the igniter. Very easy, just used an ohmeter. Unplugged the 2 pin wire connector and checked for continuit
... Read more
y. 1 lead on 1 pin and the other on the other pin., igniter side not the harness side from the dryer. A good igniter should read less than 5 ohms. I don't know the spec. exacttly, but it should not read open or infinite resistance. My meter read an open circuit. Removed the tube and igniter assembly, mine only 2 small bolts. I found the igniter element cracked. Ordered and installed igniter and tube assembly. This was a very easy install. 20 year old dryer works great and it's better than spending $500.00+ on a new one.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
No heat, would not light because igniter burnt out
6 of 8 people
found this instruction helpful.
-
anthony from Port Arthur, TX
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two scr
... Read more
ews. Plug in dryer and there you go drying clothes again. Wife all happy again.
Read less
Was this helpful?
Thank you for voting!