110689 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer tumbled but would not heat
14 of 14 people
found this instruction helpful.
-
LARRY from NEWNAN, GA
- Easy
- 15 - 30 mins
-
Pliers, Socket set
Used socket set to remove the two hex-head screws from the bottom flange of the toe panel. Manually pulled the panel out at the bottom, pulled down, and removed the panel. Looked to right and found heater shield. Removed heather shield using socket set. Removed the two wires from the terminal block (had to use a little WD40 to loosen c
... Read more
onnection and wiped up afterwards). Removed the holding screw holding the heating element using the socket set. Pulled HARD on old heating element using pliers and a rag (protection from accidental cut-sharp edges). Once out, the new element slid in relatively easy. Screwed the new element back into place and re-connected the element wires, then put the heater shield back into place. Put the toe panel back into place. Tested and worked great! The only thing that made this "easy" but not "really easy" is that I had to really pull HARD on the old element to get it out...with the sharp edges and tight fit in play, you'll need to pay attention to safety when removing the old element.
Read less
Was this helpful?
Thank you for voting!
Dryer wouldn't stay started after button was pushed.
18 of 27 people
found this instruction helpful.
-
Mike from Gainesville, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed the back of the dryer panel and replaced the relay that was not working. The dryer then worked for the next weekend of laundry then the dryer did the same thing at the end of our chores. I then pulled the panel back off and found the control pane (eend heat control) was burned up. I ended up buying a new dryer , a different brand
... Read more
of course, the next weekend. I want to thank your site for all the help. I otherwise would have spent much more on a repairman on items I did/could do myself.
Read less
Was this helpful?
Thank you for voting!
Dryer would not turn
15 of 18 people
found this instruction helpful.
-
Kim K from Hurst, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do
... Read more
the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you
Read less
Was this helpful?
Thank you for voting!
Loud sreeching and vibration
14 of 15 people
found this instruction helpful.
-
Robert from TUTTLE, OK
- Really Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
I just followed the videos I received with the order and everything went really well. This dryer was a little different than the video, but the process was the same. The HE3 does require 4 drum rollers and I had only ordered 2. However, there was only one bad roller, so I installed both on the back of the drum. The two front rollers are
... Read more
pretty easy to get to if they go bad. The idler pulley was completely worn out with an 1/8 inch groove worn off to one side. PartSelect made this an easy project!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Thermal fuse was bad.
16 of 22 people
found this instruction helpful.
-
Brad from Odessa, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Did an Ohm test on the old Thermal Fuse found it to be bad. Replaced it with a new and the dryer is back to working great. Your suggestions saved approximatley $150.
Thanks for the help.
Thanks for the help.
Was this helpful?
Thank you for voting!
Dryer made a terrible screeching noise when tumbling.
13 of 14 people
found this instruction helpful.
-
Richard from SAUGERTIES, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
Was this helpful?
Thank you for voting!
Dryer gasket detached from screen
14 of 17 people
found this instruction helpful.
-
Richard from Duarte, CA
- Really Easy
- Less than 15 mins
Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.
Was this helpful?
Thank you for voting!
Lint has been bypassing the lint filter and building up in the fan (and duct)
12 of 12 people
found this instruction helpful.
-
David from PINETOWN, NC
- Really Easy
- Less than 15 mins
I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan
... Read more
wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.
Read less
Was this helpful?
Thank you for voting!
The dryer suddenly started running cold - it would turn, the timer worked...but no heat. My wife mentioned that it had been taking longer and longer to dry a load of clothes....
12 of 12 people
found this instruction helpful.
-
Geoff from Farmington, CT
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Popped the lower cover off the dryer, found the thermal fuse and thermostat mounted on the heating tube. Removed the screws with a nutdriver, swapped wires to the new parts, and reinstalled. Then I spent 30 minutes vacuuming 13 years worth of lint and crud out of the machine - it was pretty gummed up in spots, which is probably the cause
... Read more
of the failure.
I have a 25 foot run of hose from the dryer outside, so I replaced that with 4" metal ducting. Clothes dry much faster now!!! Maybe my electric bill will go down (fat chance :) )
I have a 25 foot run of hose from the dryer outside, so I replaced that with 4" metal ducting. Clothes dry much faster now!!! Maybe my electric bill will go down (fat chance :) )
Read less
Was this helpful?
Thank you for voting!
Door latch (female part) was broken.
11 of 11 people
found this instruction helpful.
-
JEANMARIE from BELLEROSE, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
Rear dryer drum seal came out
17 of 29 people
found this instruction helpful.
-
William from Pontiac, MO
- Easy
- More than 2 hours
-
Screw drivers, Socket set
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Was this helpful?
Thank you for voting!
Would not start
12 of 15 people
found this instruction helpful.
-
Drew from Alachua, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
First I tried a new switch, This did not fix the problem. Then I replaced the Fuse in the back of the unit.
Was this helpful?
Thank you for voting!
Start switch didn't work, dryer ran when door closed
12 of 15 people
found this instruction helpful.
-
Robert from Corvallis, OR
- Really Easy
- 15 - 30 mins
-
Socket set
I removed 5 screws from the back of the top panel, removed the back panel, removed the start button from front of dryer, twisted the old start switch from the back, removed the two leads, reinstalled new part in reverse order. It was that simple! 15 minutes top. Dryer works fine. Gave me a chance to vacuum out all the dust bunnies and
... Read more
clean out the dryer vent pipe as well.
Thanks!
Thanks!
Read less
Was this helpful?
Thank you for voting!
Timer would stop the dryer with in 1 minute after set
16 of 27 people
found this instruction helpful.
-
Romeo from Holland, MI
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
Opened the back cover. Unscrewed the timer replaced the wires connected on the old timer to the new timer. Screwed the new timer in place screwed the cover back on. Then placed the timer nob on the front.
Was this helpful?
Thank you for voting!
Dryer produced no heat. My lint trap was full of wet lint.
11 of 12 people
found this instruction helpful.
-
William from LAUREL, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I saw some videos suggesting you remove the back panel.Then I saw a video where only the kick plate was removed and the element was removed that way.
I removed both the back panel and kick plate.At first I thought I was wasting my time however once I got started I was glad I removed both back and front.
There was a significant a ... Read more mount of lint in the bottom of the dryer which made it easier to remove.
It also made it easier to remove the heater element.
I hope this helps.
I removed both the back panel and kick plate.At first I thought I was wasting my time however once I got started I was glad I removed both back and front.
There was a significant a ... Read more mount of lint in the bottom of the dryer which made it easier to remove.
It also made it easier to remove the heater element.
I hope this helps.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!