110688 Kenmore Dryer - Instructions

All Instructions for the 110688
91 - 105 of 1049

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
my dryer would not heat up any longer
10 of 11 people found this instruction helpful.
  • Chris from Great Bend, KS
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screw s back in and fastend the front back on and were in bussiness!
Was this helpful?
Thank you for voting!
Door switch was broken
11 of 14 people found this instruction helpful.
  • Anthony from Orlando, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I typed in on my brouser Repair Kitchen Aid Dryer door switch.
And on You Tube up came several videos showing me how to ewmove the switch and install the new one.

The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away fro m the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada
Was this helpful?
Thank you for voting!
would not stop when opening door during cycle
10 of 11 people found this instruction helpful.
  • PHILIP from MATTHEWS, NC
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to take the time to remove dust and lint from behind the dryer. Easy repair.
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people found this instruction helpful.
  • stephen from langley, KY
  • Really Easy
  • Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people found this instruction helpful.
  • Dawn from Chesapeake City, MD
  • Really Easy
  • Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
Dryer runs heats up, will run for a short period and then shuts down, after a minute or two it will come back on and will resume drying.
18 of 36 people found this instruction helpful.
  • John from Brookings,, OR
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench set
Replaced the thermastat first, then the cutoff switch, still the same, I then replaced the thermister, and still have the problem.
Was this helpful?
Thank you for voting!
Wouldn't heat
10 of 12 people found this instruction helpful.
  • Lorraine from Elk Grove, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Wrench (Adjustable)
My husband said it was very easy and quick. We will recomend your site for sure.
Was this helpful?
Thank you for voting!
no heat
9 of 9 people found this instruction helpful.
  • Hal from Edgewater, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
unplugged from elect power.took off front lower panel.removed heater heat shield w/1/4 in nut driver,could see heat element. it looks like at thin metal twisted phone cord. i used a continuity tester to establish if there was a break in it. there was. i removed 2 1/4in screws on the right side of the element,marked wire placement slid ou t old element & slid in new one put screws back in connected wires,put heat shield back on . tested dryer ,ok good to go put on front cover.!!!!! PS sears parts wanted 15$ more
Was this helpful?
Thank you for voting!
burnt out bulb and broken switch
12 of 19 people found this instruction helpful.
  • fanny from madison, WI
  • Easy
  • Less than 15 mins
  • Screw drivers
Both my husband and I are not good at DIY or fixing things. I watched the instruction video that was posted on the PartSelect web site. It seems easy to do it, however still very skeptical. My husband decided that there is nothing to lose in trying, so we ordered the parts. It is as easy and simple as the video instruction. We are very ha ppy customers.
Was this helpful?
Thank you for voting!
The main knob insert snapped.
11 of 16 people found this instruction helpful.
  • Larry from HICKORY, NC
  • Very Easy
  • Less than 15 mins
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Was this helpful?
Thank you for voting!
The old door catch failed. Clothes won't dry with door open !
8 of 8 people found this instruction helpful.
  • Theresa from Norfolk, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Old door catch came out, new one slipped in. All works great.
Was this helpful?
Thank you for voting!
The Dryer wouldn't start after pressing the Start Button.
8 of 8 people found this instruction helpful.
  • David from CARROLLTON, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I found a video tutorial that explained the three things that are usually the problem when a dryer stops working. This showed how simple the task is. I used a multimeter to check the switch, to make certain that this was the part that needed replacement. This was part of the tutorial, as well. I ordered from PartSelect because it was rec ommended to me by an application that I use to find places where items are less expensive. The correct part arrived in a few days and it worked fine. I'm not a handyman by any means, but the tutorial showed exactly what needed to be done. It appeared simple and it was.
Was this helpful?
Thank you for voting!
Dryer Didn't Run
8 of 9 people found this instruction helpful.
  • William from Long Valley, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplugged washer,removed the two screws by the lint trap,moved the top foward lifted the top (it'shinged in the back )the switch is right inside the door top right hand corner removed the two screws that hold the switch in place used a flatblade screwdriver to seperate the connections pulled off the old installed the new switch put every thing back together worked as though it wes never broken
Was this helpful?
Thank you for voting!
Dryer was working but not generating heat.
8 of 9 people found this instruction helpful.
  • Laurie from Natick, MA
  • Easy
  • 15 - 30 mins
  • Screw drivers
I was reluctant to call a repair service. Typically when an appliance is as old as my dryer (14 years old), service people encourage you to replace, not repair. I had replaced the dryer's motor within the last 5 years and believed my dryer still had life to it. At first, I tried cleaning the lint build up from the dryer cavity and hose s. This worked but only for a couple of days. After reading other successful repair stories on the website, I decided to try replacing the thermal fuse. It was so easy. The part was easily identifiable. It was just a little hard to yank off the connecting wires. Good as new and no service call.
Was this helpful?
Thank you for voting!
Not heating
8 of 9 people found this instruction helpful.
  • Manuel from Key Biscayne, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
So simple.... I have no idea how to fix anything but I took a crack it. Looked inside and pulled out the resistor. I noticed the coil was broken so I replaced it with a newn part and reinstalled it. Worked like a charm. Saved myself alot of money!!!!
Was this helpful?
Thank you for voting!
All Instructions for the 110688
91 - 105 of 1049