110686 Kenmore Dryer - Instructions

All Instructions for the 110686
121 - 135 of 2366

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drum not turning; accompanied by loud "screeching" sound.
15 of 19 people found this instruction helpful.
  • holly from LONG BCH TWP, NJ
  • Easy
  • 30 - 60 mins
  • Socket set, Wrench (Adjustable)
Followed instructional video provided for this type of repair after diagnosing problem via of 'troubleshooting' on PartsSelect site. Simple, safe, and relatively easy (minimal mechanical knowledge helpful).
Second time using PartSelect; washing machine repair ~ 6 mo. previous.
PartSelect was spot-on with that repair as well, sa ving hundreds of dollars.....my go-to site for appliance repairs and pats....make it yours as well and you will NOT be disappointed! Fast, prompt shipping.
Was this helpful?
Thank you for voting!
Dryer would leave clothes damp
15 of 20 people found this instruction helpful.
  • Luke from Elmira, NY
  • Easy
  • Less than 15 mins
  • Nutdriver
First, I unplugged the dyer and then I removed all of the screws for the panel that covers the rear of the dryer. This exposed the cycling thermostat's location. I then removed the wires, one at a time so I would be able to put them back on in the same place. Then I removed the one screw using a nut driver and then put the new cycling the rmostat in place. It was pretty easy.
Was this helpful?
Thank you for voting!
squeaky and very loud noise
13 of 15 people found this instruction helpful.
  • Jimmie from Lucerne Valley, CA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers, Socket set
first we printed out directions from a couple of online repair sites that had pictures.
We followed the directions to remove the front of the dryer and removed the belt off the drier and then took out the drum. We had a hard time trying to keep the rear seal on so used CLOTHES PINS to put on the seal, then we added the adhesive repla cing the clothes pins until the whole seal glued. Since the drum was already out, we put it in the sun to really dry the glue.
Next we attacked the drum support rollers. We removed the back of the dryer and used a 9/16" socket with an extention to remove the back nuts.
We took out the shaft, used sandpaper on it and then replaced the triangle clips and the support rollers.
Then put the back on again, then the front, making
sure the drum fit on the front. You have to then figure out the belt, with the rubber side down, and then work with the tensioner, which took my poor husband a while. Then lowered the top, put the clips back on and the bottom, making sure we turned the drum. It was a success after about 3 hours. You can do it a lot easier with pictures.
Was this helpful?
Thank you for voting!
dryer door would not latch
13 of 15 people found this instruction helpful.
  • Robert from Livermore, ME
  • Really Easy
  • Less than 15 mins
my dryer door didn't latch for over a year. We were accustom to proping large objects against it. a friend told me to look on line. The close up pictures and parts diagrams were awesome. It was here in 4 days . Now my family thinks I am a hero. The end
Was this helpful?
Thank you for voting!
drum very loud when rotating
13 of 15 people found this instruction helpful.
  • michael from indianapolis, IN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and repl aced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.

Thanks Mike
Was this helpful?
Thank you for voting!
Quick and simple - quickest $100 I've ever saved!
13 of 16 people found this instruction helpful.
  • Kelly from Waukegan, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
Removed the two screws under the lint trap
Opened the top (had to use flathead screwdriver to release latches)
Disconnected door switch harness from front panel
Removed 2 screws holding front panel on dryer
Lifted out dryer drum (previous belt had broken)
Vacuumed inside of dryer (found $3 in quarters!)
Put n ew belt around drum
Put drum back in dryer, using empty laundry soap bottle to support its weight
Looped belt around pulley and motor; secured pulley to dryer bottom
Made sure rear gasket thingy was aligned properly and drum turned freely
Put front panel back on
Re-attached door switch
Closed top and put screws back in under lint trap
Fired it up - WOOHOO!
Was this helpful?
Thank you for voting!
the drum was not turning because a broken belt
14 of 19 people found this instruction helpful.
  • thomas from bloomfield, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers
I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum expo sed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.
Was this helpful?
Thank you for voting!
Defective Door Switch
12 of 13 people found this instruction helpful.
  • George from Bedford, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Opened the lid and removed screws hollding switch to cabinet. Had to use magnifying glass to find locking mechanism on the electrical harness. Used small bladed screwdiver from my computer maintenaqnce kit to disengae lock. Hooked up harness. Replaced screws and shut lid. Main difficulty is my near vision. Requires use of a magnifier I a m 80 years old). Your video is great. Gives step by step instructions.
Was this helpful?
Thank you for voting!
Dryer door switch
12 of 13 people found this instruction helpful.
  • Frank from STANFORDVILLE, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
We watched the video on ur website! Thank you
Was this helpful?
Thank you for voting!
Door latch (female part) was broken.
11 of 11 people found this instruction helpful.
  • JEANMARIE from BELLEROSE, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
Drum would not turn and drum seal old
12 of 15 people found this instruction helpful.
  • Geraldine from Stacyville, ME
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
Watch the utube video a few times. Followed instructions. Marked all screws. Cleaned the inside of dryer where motor is. Replaced drum seal and then belt. I replaced front of dryer screwed everything in place and I did it. Holding drum in place while installing front of dryer was hard as it was heavy but I did it m. My friends and husband couldn’t believe it. Utube is great!
Was this helpful?
Thank you for voting!
Bearings wore out of drum rollers
11 of 12 people found this instruction helpful.
  • Judy from Kalamazoo, MI
  • Easy
  • Less than 15 mins
  • Screw drivers
I raised the top of the dryer, removed the front, the belt and the drum. Slipped off old rollers, installed new ones and new tensioner. Reinstalled drum and belt, bolted front back on and closed the top.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Motor wore out
12 of 15 people found this instruction helpful.
  • Charles from Clarissa, MN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I took the dryer apart ( using a repair book ) It was Super Simple to do I only needed a extra set of hand's to hold the drum in place while reassembling it. removed the hold down snap on collar's on the Motor ( after removing the Blower from the back of the dryer ( super simple. Extra set of hand's needed ) Reassembled in the same order. And now The Dryer work's like NEW..Shure Beat Buying a new Dryer..
Was this helpful?
Thank you for voting!
Dryer timer stopped working
13 of 18 people found this instruction helpful.
  • James from Park City, UT
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Unfortunately it is not easy to get to this part due to the fact the control panel is attached to the top of the dryer by both plastic clips and screws. I was able to bend the back down in the back to gain access to the two screws that held the dryer timer in place. This job is much easier if you have an assistant to hold the thin tin o r steel backing away from the control panel while reconnecting the wire sensors to the new timer. This is the second time I have used Parts Select they are excellent and their prices are very competitive. The part was identical to the broken part. I saved at least $100 by doing the job myself.
Was this helpful?
Thank you for voting!
All Instructions for the 110686
121 - 135 of 2366