110684 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The Dryer was working normally, just no heat
19 of 22 people
found this instruction helpful.
-
Andrew from Roslyn Heights, NY
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Very Very Easy all you need is a 1/4 inch nutdriver. 1st remove the screws from the back of the dryer. 2nd you will see a shaft like duct work. remove the 2 screws from this shaftway, lift out the old heating element and replace with the new element. Part select was right on target and fast. 2 days to recieve my order. I expected to hav
... Read more
e to buy a new appliance. Partselect made it possible to fix it like new for around $80.00
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Door Gasket tore out
17 of 17 people
found this instruction helpful.
-
Manolak from MURFREESBORO, TN
- Easy
- Less than 15 mins
Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine....
Was this helpful?
Thank you for voting!
Drum was binding because of worn bearing supporting front of dryer drum
23 of 35 people
found this instruction helpful.
-
Leslie from Townsend, GA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to gl
... Read more
ue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!!
Read less
Was this helpful?
Thank you for voting!
No heat in dryer
18 of 21 people
found this instruction helpful.
-
Kenneth from Durham, NC
- Easy
- 15 - 30 mins
-
Nutdriver
Once I unpluged the dryer and then removed the back cover, I located the heating unit and then removed the thermostat. Once that was done, I installed the new thermostat and connected the wires. I tested the dryer to make sure that it would heat. Then I replaced the back cover.
Was this helpful?
Thank you for voting!
dryer sounded like I was strangling a dog
18 of 21 people
found this instruction helpful.
-
Lynda from Syracuse, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First, I watched a utube video of replacing the dryer belt. Then I went to Sears Hardware and couldn't find a part. Then I ordered the parts for my favorite online repair parts source - partselect.com. I had the part in one day! We did exactly what the video showed and also replaced the two wheels that looked like roller blade wheels. Pie
... Read more
ce of cake. Saved a $75 repair call plus whatever the parts would have been and spent about 20 minutes doing it. Back in business. Great for a 12 year old dryer! Buy the dryer kit!
Read less
Was this helpful?
Thank you for voting!
Broken push to stat switch
18 of 21 people
found this instruction helpful.
-
Charles from Fairfax, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed back cover, removed broken switch, replaced with new switch, replaced back cover, told wife her dryer was fixed.
Was this helpful?
Thank you for voting!
dryer not working
22 of 33 people
found this instruction helpful.
-
Maura from Newtown, CT
- Really Easy
- Less than 15 mins
After unplugging and removing the back cover from the dryer, locate the push button switch. Slide putty knife around outer cover to unhook catch. Replace with new push button switch. My dryer is still not working, but this was a simple replacement.
Was this helpful?
Thank you for voting!
Squeaky Dryer
17 of 19 people
found this instruction helpful.
-
Daniel from Hamilton, OH
- Easy
- 15 - 30 mins
-
Screw drivers
I looked for squeaky dryer within parts select and went with the 80%. I received the Maintenance Kit, replaced two rollers and it works like new. Amazing since this is the first time I have ever opened a dryer. The instruction sheet and parts were all I needed.
Was this helpful?
Thank you for voting!
Dryer continued to run with door open
18 of 23 people
found this instruction helpful.
-
Colleen from CAPE CORAL, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
The video provided by this site on YouTube on this topic was perfect. Saved us a couple of hundred dollars DIY rather than repair man.
Was this helpful?
Thank you for voting!
Loudly clunking clothes drum due to worn out roller
17 of 20 people
found this instruction helpful.
-
KENNETH from WEST ORANGE, NJ
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Followed video on Parts Select site for comparable model showing roller and drive belt replacement.
The triangle plastic retaining clips were the most difficult part , to put
on and take off. They required careful , firm stretching with needle nose pliers.
The triangle plastic retaining clips were the most difficult part , to put
on and take off. They required careful , firm stretching with needle nose pliers.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would intermittently work on economy drying, never on timed dry. (Heat failed tumbler was always good)
17 of 20 people
found this instruction helpful.
-
Steve from HICO, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Disconnect power cord. Removed upper and lower panels. Disconnected "push on" spade connectors and removed the single screw holding each device and removed same. Timer had a two multi wire plug and 2 screws. Reversed process and installed same. Was fairly sure only timer was bad. But due to age of dryer and posts found here, decided to ju
... Read more
st install fuse and cut out. Everything works perfect!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Drum spinning but no heat
19 of 27 people
found this instruction helpful.
-
Chad from Derby, KS
- Easy
- 15 - 30 mins
-
Socket set
Purchased thermal cut off kit but only replaced the top most thermostat. There were some extra wires wired into the bottom thermostat, that were not described on the video or any other repair user posts. It checked fine on my multimeter anyway.
Was this helpful?
Thank you for voting!
Getting to hot and shutting off after 20 minutes
16 of 18 people
found this instruction helpful.
-
William from `Omak, WA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I watched the installation video on both parts before I purchased them and it was a piece-of-cake after that.
Other Parts Used:
Was this helpful?
Thank you for voting!
part number was different from the original, but it fit just fine.
20 of 30 people
found this instruction helpful.
-
John from Bristol, CT
- Easy
- Less than 15 mins
installed the new dryer lint screen, it fit perfectly
and is now in operation.
and is now in operation.
Was this helpful?
Thank you for voting!
Dryer kept spinning when the door opened
16 of 18 people
found this instruction helpful.
-
Gary from Ocean Springs, MS
- Really Easy
- Less than 15 mins
-
Screw drivers
Came to Parts Select. Looked for door switch. Read what other people did. Part came in a few days took a few minutes to take old switch out (had to pry the plastic connection apart with little thin screwdriver). Everything was easy
Was this helpful?
Thank you for voting!