1106808601 Kenmore Dryer - Instructions

Used the dryer illustrated parts list to find the heater. Used a multi-meter to determine that the heater had no resistance, meaning it was open and could not heat. Removed the heating element held to the dryer with one hex screw with a wrench. Purchased a replacement heating element and received it within 2 days. Screwed the new heating element with a hex wrench again. The dryer works like new now.

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

pulled out the old one and put in the new one. I wish all repairs were this easy. I also had to reattach the vent hose, which is annoying because I'm the only one who fits behing the dryer without disconnecting the gas. I never touch the gas related parts.

I appreciate how easy your website made it, to get the parts, I would recomend this site and will be back myself.

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

Disassembled dryer, removed tumbler, replaced drum support rollers

Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed clip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.

1 Vice grips are required to remove the fan/blower. Clamp on inside of dryer so you can remove the blower/fan assembly

Recommend 10" or larger 14" will definitely do the job

2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatural

3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example

removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business

One screw held element. Removed back of dryer. Removed screw, pulled out failed element. Slid new element in. Put in and tightened screw. Replaced back. Only two problems: screw head was pointed away; replacing air duct to wall tube (always is a problem for me).

Removed what was left of the old hinges, installed the new ones. Also added a length of jack chain (same size chain that’s on a toilet flapper) to one side to support the door while open. Tried to chain up both sides but it wouldn’t let the door completely close and depress the switch. Cables are no longer supplied by any parts dealers.

I replaced the springs and cables in the dryer door.

Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.

I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.

Replaced lid switch, but problem still continued.