1106803 Kenmore Washer - Instructions

All Instructions for the 1106803
46 - 60 of 91

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door latch snapped off.
1 of 2 people found this instruction helpful.
  • Karen from Randle, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
We got the part so fast we were both surprised. My husband installed the part by just seeing how the old one came off. It was simple and fairly quick. Except that his hands are so big they had a hard time fitting in to where the part needed to go. Just opened the top of the dryer, took the old part out and put the new one in.
Was this helpful?
Thank you for voting!
Broken door actuator spring -interposer for motor control
1 of 2 people found this instruction helpful.
  • Stephen from Vancouver, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Followed previous comments and took 5 minutes to replace. Be careful to hold spring and switch together because easy to separate and drop. Two screws to remove for switch, two to remove for lint trap, pop the lid up and switch / spring is easy to access.
Was this helpful?
Thank you for voting!
Received part in 3 days from ordering. I was surprised when it showed up at my front door so quickly. Less than 1/2 hour later we were drying laundry again. Very impressed with the speed of service and the price.
2 of 5 people found this instruction helpful.
  • Patrick from Ramsey, MN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First removed 2 screws on lint remover vent. Used a screw driver to force up top of dryer from out front. These will require pressure to pop the top off the dryer. Once the top was up I could reach the actuator and remove the 2 screws holding it. Once removed just replaced with new actuator and bam, done. Snapped top of dryer back on a nd reinstalled 2 screws on lint vent and Done. Easy, no problem....Thank you PartSelect!!.
Was this helpful?
Thank you for voting!
Old hot water inlet hose had budge at both ends.
2 of 5 people found this instruction helpful.
  • Jimmy from MEMPHIS, TN
  • Very Easy
  • Less than 15 mins
  • Pliers
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this helpful?
Thank you for voting!
washer continued to spin when you raised the lid not shutting off
1 of 2 people found this instruction helpful.
  • Daniel from TRENTON, NJ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.
Was this helpful?
Thank you for voting!
Lid switch failed, dryer stopped working
1 of 2 people found this instruction helpful.
  • Rick from BETHESDA, MD
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this helpful?
Thank you for voting!
washer would fill with water but not start
5 of 15 people found this instruction helpful.
  • Edward from Nanuet, NY
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at
Was this helpful?
Thank you for voting!
Lever was broke off
0 of 1 people found this instruction helpful.
  • linda from las cruces, NM
  • Easy
  • 15 - 30 mins
  • Screw drivers
I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!
Was this helpful?
Thank you for voting!
Washing machine over 20 years old but still runs strong door switch actuator spring broke original spring was not availible.
0 of 1 people found this instruction helpful.
  • Larry from Elmhurst, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers
drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.
Was this helpful?
Thank you for voting!
Couldnt get the dryer to turn on even when i had power.
0 of 1 people found this instruction helpful.
  • Kevin from Tonica, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!
Was this helpful?
Thank you for voting!
Wife pulled bed sheets out of drier and broke door switch actuator
0 of 1 people found this instruction helpful.
  • Ernest from Moundsville, WV
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.
Was this helpful?
Thank you for voting!
Dryer stopped working
0 of 1 people found this instruction helpful.
  • Mike from Conway, AR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen th e two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.

Advice: Don't slam the dryer door. The actuator will last longer.
Was this helpful?
Thank you for voting!
the dryer would not turn on
0 of 1 people found this instruction helpful.
  • James from Shortsville, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in ab out 10 minutes.
Was this helpful?
Thank you for voting!
the door switch broke, and I had to pop the lid unscrew the switch and use a clothespin to depress the switch acuator button....not pretty.
0 of 1 people found this instruction helpful.
  • Greg from Phoenixville, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
same as I described above. However i was amazed when the part showed up the very next day...I was expecting maybe 3 or so days later. I wiil absolutely use PartSelect in the future.
Was this helpful?
Thank you for voting!
Dryer would not turn on, found metal clip in laundry
0 of 1 people found this instruction helpful.
  • Terry from Carlsbad, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's pre ss fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.
Was this helpful?
Thank you for voting!
All Instructions for the 1106803
46 - 60 of 91