110679 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Unit not spent
4 of 4 people
found this instruction helpful.
-
Boonkham from SMYRNA, TN
- Really Easy
- 30 - 60 mins
-
Nutdriver
Just replaced part
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer was squealing
4 of 4 people
found this instruction helpful.
-
Kevin from VALDOSTA, GA
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.
Was this helpful?
Thank you for voting!
Dryer ran but without heat.
4 of 4 people
found this instruction helpful.
-
barbara from SOUTHAMPTON, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Turned off my circuit breaker first. Removed back panel with a 1/4 nut driver. Replaced the dryer fuse first. Very easy but did not fix the problem. Watched how to videos to narrow down the parts I might need. Purchased the thermal cut off kit. Installed the High limit thermostat first. Tested the dryer, no dice. Finally installed the The
... Read more
rmal cutoff. BAM!! I have heat. Since this is an older dryer I did need to use some WD40 to loosen some of the connections. Total cost of parts including tax and quick delivery was $48.30. Fantastic. My old man told me it was unfixable. He was wrong. I WIN. This site is a great teaching site. Thank you!
Read less
Was this helpful?
Thank you for voting!
Idler pulley seized
4 of 4 people
found this instruction helpful.
-
John from CREST HILL, IL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and rem
... Read more
ove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.
Read less
Was this helpful?
Thank you for voting!
Taking 90 minutes + to dry one load
5 of 7 people
found this instruction helpful.
-
Bryan from newington, CT
- Easy
- 15 - 30 mins
-
Socket set
Removed the back of the dryer about 8 screws. Removed the Thermostat 250 F and replaced with new. Dries a load of clothes in one cycle on medium. Not bad for a 16 dollar part. I am a computer tech and I am used to taking computers a part but I think most people that are in anyway mechanically inclined and can look at a diagram could d
... Read more
o this and save yourself a lot of money.
Read less
Was this helpful?
Thank you for voting!
When door was closed the timer could be heard to continue clicking. also, drying cycle started immediately upon closing the door.
5 of 7 people
found this instruction helpful.
-
Theodore from Baraboo, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver
Two screws hold the top control panel in place. Once removed the panel could be tipped forward. The Push to Start switch had 2 wires which were removed and swapped to the new starter switch. The old one rotated 90 degrees to remove and the new one installed. Panel was resecured to the top of the dryer and tested. Worked first time.
... Read more
Finding the part on the website, ordering it, receiving it quickly and the install couldn't have been easier or more pleasant or efficient.
Read less
Was this helpful?
Thank you for voting!
Dryer drum turned hard because rollers were worn
4 of 4 people
found this instruction helpful.
-
Paul from STONE CREEK, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this helpful?
Thank you for voting!
drier would not heat up
5 of 7 people
found this instruction helpful.
-
PATRICK from PALOS PARK, AL
- Easy
- Less than 15 mins
-
Screw drivers
i took off the back of the drier and with a screw driver removed the 2 screws and put the new part on
Was this helpful?
Thank you for voting!
Dryer would not stay running if I placed the timer on anything above 30 min
4 of 4 people
found this instruction helpful.
-
Cristy from HARROGATE, TN
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I took the timer knob off, then took the back off. I then took a picture of the so I would know how the wires would go back but I didn't need because the timer is labeled. I then took the timer out snapped wires off then replaced them on the new one and bolted it back it. It was very easy and took less than 15 min to do.
Was this helpful?
Thank you for voting!
Dryer wouldn't heat.
4 of 5 people
found this instruction helpful.
-
Stan from Boswell, OK
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal F
... Read more
use blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.
Read less
Was this helpful?
Thank you for voting!
My idler pully was squealing
4 of 5 people
found this instruction helpful.
-
Anthony from SAINT CLOUD, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it
... Read more
took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.
Read less
Was this helpful?
Thank you for voting!
Roller Berings were worn out - replaced both
4 of 5 people
found this instruction helpful.
-
Gregory from COCOA, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair
Was this helpful?
Thank you for voting!
Element not heating up.
4 of 5 people
found this instruction helpful.
-
Phillip from Breinigsville, PA
- Easy
- 15 - 30 mins
-
Screw drivers
Opened access door, noticed main power wire to heating element was partially melted. This was caused by a bad connection to the drying element, loose. Removed heating element assembly. Cut bad section of wire and added new connection. While doing this the thermostats plastic casing cap came off ! Probably due to exessive heat / resistanc
... Read more
e from the bad connection. This confirmed why there was no heat. Intalled new thermostat and and am now good to go !
Read less
Was this helpful?
Thank you for voting!
Elerctric Dryer Push Button Start
3 of 3 people
found this instruction helpful.
-
Patricia from OCEAN PARK, WA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I am a 75 yr old woman. I cannot afford to have a service call plus parts. So I ordered the part from this company and used the video instructions to install. Now this should have been a 15 minute process but I was being careful.. I installed and pushed start and Hooray I did it
Was this helpful?
Thank you for voting!
Clothes were not drying on auto sensor.
3 of 3 people
found this instruction helpful.
-
Michael from Annapolis, MD
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.
Was this helpful?
Thank you for voting!