110679 Kenmore Dryer - Instructions

All Instructions for the 110679
76 - 90 of 616

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer stopped working mid cycle restarts after resetting lid
12 of 17 people found this instruction helpful.
  • Eric from West Chester, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.
Was this helpful?
Thank you for voting!
Idler pulley wore out
10 of 11 people found this instruction helpful.
  • Peter from HUEYTOWN, AL
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.
Was this helpful?
Thank you for voting!
my dryer would not heat up any longer
10 of 11 people found this instruction helpful.
  • Chris from Great Bend, KS
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screw s back in and fastend the front back on and were in bussiness!
Was this helpful?
Thank you for voting!
no heat
9 of 9 people found this instruction helpful.
  • Hal from Edgewater, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
unplugged from elect power.took off front lower panel.removed heater heat shield w/1/4 in nut driver,could see heat element. it looks like at thin metal twisted phone cord. i used a continuity tester to establish if there was a break in it. there was. i removed 2 1/4in screws on the right side of the element,marked wire placement slid ou t old element & slid in new one put screws back in connected wires,put heat shield back on . tested dryer ,ok good to go put on front cover.!!!!! PS sears parts wanted 15$ more
Was this helpful?
Thank you for voting!
Dryer squeeching very loud
9 of 9 people found this instruction helpful.
  • Michael from ENOLA, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people found this instruction helpful.
  • stephen from langley, KY
  • Really Easy
  • Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people found this instruction helpful.
  • Dawn from Chesapeake City, MD
  • Really Easy
  • Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
Wouldn't heat
10 of 12 people found this instruction helpful.
  • Lorraine from Elk Grove, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Wrench (Adjustable)
My husband said it was very easy and quick. We will recomend your site for sure.
Was this helpful?
Thank you for voting!
Dryer runs heats up, will run for a short period and then shuts down, after a minute or two it will come back on and will resume drying.
18 of 36 people found this instruction helpful.
  • John from Brookings,, OR
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench set
Replaced the thermastat first, then the cutoff switch, still the same, I then replaced the thermister, and still have the problem.
Was this helpful?
Thank you for voting!
The old door catch failed. Clothes won't dry with door open !
8 of 8 people found this instruction helpful.
  • Theresa from Norfolk, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Old door catch came out, new one slipped in. All works great.
Was this helpful?
Thank you for voting!
Not heating
8 of 9 people found this instruction helpful.
  • Manuel from Key Biscayne, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
So simple.... I have no idea how to fix anything but I took a crack it. Looked inside and pulled out the resistor. I noticed the coil was broken so I replaced it with a newn part and reinstalled it. Worked like a charm. Saved myself alot of money!!!!
Was this helpful?
Thank you for voting!
Dryer Would Not Heat
8 of 10 people found this instruction helpful.
  • John from Raleigh, NC
  • Easy
  • 15 - 30 mins
  • Socket set
The dryer stopped heating. Took the front lower panel off of the dryer and obtained the troubleshooting instructions stored there. Used an ohmmeter (most volt meters also have an ohmmeter) and tested all the electrical components one by one (thermostat, thermal fuse, heater coil - following the troubleshooting instructions provided with the dryer) and found that I didn't have any resistance across my heater element. Removed it and sure enough there was a break in the heater coil. Ordered a new heater element from PartSelect for less than $50 and replaced it myself. Saved myself a good bit of money repairing my dryer myself. It was very straight forward and easy. If you can follow easy to read instructions you can do it.
Was this helpful?
Thank you for voting!
Dryer would not turn on
8 of 10 people found this instruction helpful.
  • Pam from Chandler, AZ
  • Really Easy
  • Less than 15 mins
  • Socket set
We took the screws off of the back, took out the thermal fuse and replaced it with the new one.
We watched a video of how to do it which made it so easy.
Works great!
Was this helpful?
Thank you for voting!
Dryer working, but not heating
9 of 13 people found this instruction helpful.
  • Amy from Birmingham, AL
  • Really Easy
  • Less than 15 mins
  • Socket set, Wrench set
Took back cover off
Disconnected part
Put new one in
Reconnected wires
Put back cover on

To verify that this was the needed part, I used a digital multimeter to confirm there was no continuity.
Was this helpful?
Thank you for voting!
The dryer door latch broke
9 of 13 people found this instruction helpful.
  • Theresa from Topeka, KS
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.
Was this helpful?
Thank you for voting!
All Instructions for the 110679
76 - 90 of 616