110679 Kenmore Dryer - Instructions

All Instructions for the 110679
31 - 45 of 616

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer not spinning
33 of 49 people found this instruction helpful.
  • john from goldsboro, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)
Was this helpful?
Thank you for voting!
Felt piece coming out of filter
27 of 33 people found this instruction helpful.
  • Sara from Solon, IA
  • Really Easy
  • Less than 15 mins
Removed old filter and put in new one.
Was this helpful?
Thank you for voting!
Dryer wouldn't heat
25 of 27 people found this instruction helpful.
  • Suzanne from Saint Francisville, IL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Following the very helpful instructions that I found at PartSelect.com I was able to open the dryer and access the heating element which I suspected was bad. I realized later that I didn't need to open up as much as I did but the job was easy. In the future I would only open the panel below the door to access the element.

J ust to make sure that it wasn't a problem with a thermostat or thermal fuse I also checked continuity from the temperature selector knob on the control panel to the heating element. When I verified continuity (zero resistance) I knew that the element was bad. Once I removed it I could see that one of the coils was broken and I should have just checked that first and not bothered opening up the control panel at the top.

Still it was less than an hour of work total. I have some experience with DIY projects but have not worked on appliances before. Thanks for the great site with good instructions and lower costs than the local parts counter.
Was this helpful?
Thank you for voting!
noisy drum
29 of 40 people found this instruction helpful.
  • Jeff from Mesa, AZ
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.
Was this helpful?
Thank you for voting!
Lid closes, switch wouldn't turn on machine.
31 of 47 people found this instruction helpful.
  • Kenneth from Wilmington, IL
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams. Time on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.
Was this helpful?
Thank you for voting!
craked blower motor
63 of 144 people found this instruction helpful.
  • joe from cheswick, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Was this helpful?
Thank you for voting!
The dryer was running and it quit, just stopped. A friend looked at it and thought it was this switch. I purchased the switch and he installed and it still did not work.
24 of 28 people found this instruction helpful.
  • Debbie from Mooresville,, IN
  • Easy
  • Less than 15 mins
  • Nutdriver
No, if that had of been the problem, it would have worked. However, I called a service man out to look at it. It was a fuse that does not look like a fuse. I had the system already torn apart and cleaned. The service took a meter and checked the fuse ( that did not look like a fuse) and it was bad. It cost 14.00 for the fuse, it took less than 5 minutes for installation and the service fee was $65.00. My advise, get a meter, check everything yourself, and only purchase what you need.
Was this helpful?
Thank you for voting!
Poorly designed lint filter/ gasket falls off
25 of 34 people found this instruction helpful.
  • John from Madison, WI
  • Really Easy
  • Less than 15 mins
Replaced
Was this helpful?
Thank you for voting!
Needed to change rear exhaust to the side to fit dryer into my closet.
44 of 91 people found this instruction helpful.
  • Mark from San Diego, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.
Was this helpful?
Thank you for voting!
Dryer runs with no heat
23 of 29 people found this instruction helpful.
  • Paul from Bradford, MA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
It was easier to remove the blower manifold cover, (3 screws) to get at the heater element. Remove the heat shield, disconnect the two wires from the element. There is another screw on the side holding the element in the housing. Remove it and slide the element torward you. I used pliers as it was a snug fit. Replace. Good time to vacuum the whole area.
Was this helpful?
Thank you for voting!
The dryer stopped working and would not start.
20 of 22 people found this instruction helpful.
  • kevin from Saint Augustine, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
After unplugging the dryer, I removed the bottom panel in front. Remove the the filter inside the dryer and remove the filter housing below. There you can see the thermal fuse on the air duct, its white with two blue wires. You can check it with a ohmmeter after removing the wires. If its open its bad. Its held in place with two sheet met al screws. After replacing the thermal fuse the dryer worked fine. However I would suggest cleaning the air duct and the outside discharge opening. Hope this helps.
Was this helpful?
Thank you for voting!
Idler Pulley broke
21 of 26 people found this instruction helpful.
  • Keith from Richmond, VA
  • Really Easy
  • 15 - 30 mins
  • Socket set
I disconnect the power, then the vent pipe. I removed the back panel of the dryer to access the pulley and removed the belt. Replaced the back and put everything back together.
Was this helpful?
Thank you for voting!
Moisture sensors need replacement
20 of 24 people found this instruction helpful.
  • Jack from JONESBORO, AR
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor.
Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in h andy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.
Was this helpful?
Thank you for voting!
Washer would fill up, wash, then stop
22 of 31 people found this instruction helpful.
  • Glen from Plano, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I deduced the lid switch was the problem.

I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed it on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.

The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.
Was this helpful?
Thank you for voting!
Insanely loud squeaking
17 of 17 people found this instruction helpful.
  • Stacy B. from MUKWONAGO, WI
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
With the correct parts and watching the video, it was so easy to repair. We ordered the wrong part (for the Electric Dryer when it should have been for the Residential Dryer) but the return was easy and we got the new parts super fast. Next time I would probably look at the offending part first before ordering just to make certain. But w e used a socket set and Philips screwdriver and actually had our teens do all the work for experience. Fixed the loud noise one and for all.
Was this helpful?
Thank you for voting!
All Instructions for the 110679
31 - 45 of 616