110677 Kenmore Dryer - Instructions

All Instructions for the 110677
106 - 120 of 2659

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
craked blower motor
63 of 144 people found this instruction helpful.
  • joe from cheswick, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Was this helpful?
Thank you for voting!
Broken door switch
24 of 27 people found this instruction helpful.
  • Michael from Maricopa, AZ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Followed your online video for disassembly and it was not only educational but actually quite simple. I would recommend that you start the video with," make sure the power cord is disconnected from the power source". I have worked on numerous pieces of large electrical equipment and would strongly suggest this be added. Some people think if it's, "off", it's safe. Your phone staff when ordering was great. We will do business again.
Was this helpful?
Thank you for voting!
Kenmore 70 series dryer wouldn't stop running
24 of 28 people found this instruction helpful.
  • Greg from Sykesville, MD
  • Easy
  • 15 - 30 mins
  • Screw drivers
The start switch on my Kenmore dryer was bad, causing the dryer to go into another timed cycle once it completed one cycle, and it would keep going until we unplugged it or left the door open. I repaired the switch at first, but after a couple of months the contacts bent again, so I just decided to replace it.

The new switch f rom PartSelect.com was only $8 or so plus shipping. Once I got the switch, I removed the rear access panel, disconnected the bad switch, and replaced it with the new switch. I closed the dryer up and it worked beautifully.

You can find detailed instructions on replacing the push-to-start switch on a Kenmore 70 series dryer on Fixya.com:
Was this helpful?
Thank you for voting!
Dryer would quit before the end of the cycle
24 of 28 people found this instruction helpful.
  • Ernest from Beaumont, TX
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
My wife reported that the dryer was not working. I checked it and it seemed to work fine. This went on for about a month or two. Every time I checked it, it started just fine.

Well, she threatened to go buy a new dryer, I took her more seriously. I thought perhaps a thermal protection was the cause. But when I dug into it, I learned that when those trip out, they are permanent (have to be replaced).

I finally noticed loud humming sound the motor made at start-up, when it failed to start turning on one occasion and eventually tripped out the motors thermal protection.

I ordered the new drive motor form PartSelect.com.

Replacing the motor was fairly easy if you like to take stuff apart. One thing that I had not anticipated was that the two foam gaskets on the exhaust duct were dry rotted. I went to my local part supplier to get them. They did not have them in stock. :( While I was there, I asked how much the motor was, they wanted $50 more than PartSelect.com :D

I put it back together without the new gaskets, and it runs like new. I ordered the gaskets from PartSelect and will add them when they arrive.

My wife is happy again, she can bust out the laundry in one day; it had been taking here all weekend.

I learned to take her at her word.
Was this helpful?
Thank you for voting!
Noisy Dryer
22 of 22 people found this instruction helpful.
  • Patrick from SCHENECTADY, NY
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
I ordered the dryer repair kit and to my surprise it arrived 4 days early. I followed the video instructions on the parts select website to replace 4 rollers, belt and belt pulley. A 1/4 in nut driver attached to my Dewalt drill made life ALOT easier!! My recommendation, when you remove the rollers, take a rag and really clean up the shaf t they ride on. Then apply a lightweight spray oil to the shafts. When you install the new rollers they will spin free and easy. Having the dryer apart is also a great time to break out the dust buster of vacuum. Spin the fan motor up front by hand and use vacuum to remove lint or belt shaving from inside the cabinet. Add this step as good fire prevention measure.
Was this helpful?
Thank you for voting!
The old lint screen on the dryer was broken
24 of 30 people found this instruction helpful.
  • Bill from Farmington Hills, MI
  • Really Easy
  • Less than 15 mins
I analyzed the situation to see how to remove the old lint screen. I carefully pulled out the old lint screen. I was careful not to drop it. With caution, I placed the old lint screen in the trash receptacle that was nearby. Next, I opened the box that the new lint screen came in with a sharp knife. I removed the new lint screen from the box, took off the plastic wrap and inserted the lint screen in the same slot that the old one used to be in. I tested that it was seated correctly by pulling it out and reseating it in the slot. The true test came when I ran my first load of laundry through the dryer. The total repair time for this fix was 14.92 seconds.
Was this helpful?
Thank you for voting!
too long to dry
21 of 22 people found this instruction helpful.
  • Victor from San Antonio, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then connect the two wires into new element, and put the element back in place, and put the back cover, now it getting really hot, and save me a lot of time and money on energy too.
Was this helpful?
Thank you for voting!
Poorly designed lint filter/ gasket falls off
25 of 34 people found this instruction helpful.
  • John from Madison, WI
  • Really Easy
  • Less than 15 mins
Replaced
Was this helpful?
Thank you for voting!
Needed to change rear exhaust to the side to fit dryer into my closet.
44 of 91 people found this instruction helpful.
  • Mark from San Diego, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.
Was this helpful?
Thank you for voting!
Dryer runs with no heat
23 of 29 people found this instruction helpful.
  • Paul from Bradford, MA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
It was easier to remove the blower manifold cover, (3 screws) to get at the heater element. Remove the heat shield, disconnect the two wires from the element. There is another screw on the side holding the element in the housing. Remove it and slide the element torward you. I used pliers as it was a snug fit. Replace. Good time to vacuum the whole area.
Was this helpful?
Thank you for voting!
No heat, everything else worked fine.
22 of 26 people found this instruction helpful.
  • STEVEN from MORA, MN
  • Easy
  • Less than 15 mins
  • Nutdriver
Installed the new High Limit Thermostat onto the new Heating element and installed the unit on the dryer. Wires were then connected and the dryer was tested. Repair complete. Dryer is 25 years old and this is its first repair.
Was this helpful?
Thank you for voting!
Dryer Would not start
23 of 29 people found this instruction helpful.
  • Heath from YORK, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
Repair was easy after identifying the problem. Parts select was correct with the 3 parts for trouble shooting. However I should have looked at the door switch 1st. Ordered a thermostat and On switch 1st. Then had to reorder the door switch. In the future just order all 3 to avoid the shipping charges and return what you don't need to save time and money.
Was this helpful?
Thank you for voting!
Push start and the motor would hum.
22 of 26 people found this instruction helpful.
  • Doug from Manitowoc, WI
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
**** Remove power cord from the wall****

As said earlier, you will need to lift the top. Drop the two screws holding the lint shoot and pop the top by sliding a screw driver into the corner on the front. Lif tthe top and rest against the wall behid the unit. remove the two (4 total) screws at the top and bottom of the front doo r assembly.
Place sometin under the front portion of the drum. At this point you'll see the need to clean everything! :) Slide the belt off and around the drum, (take note of the routing it takes.) Remove the drum by gently pulling it towards you. Set it aside. Clean more. :) (It is nice to have a vacuum handy.) At this point you really need to get to the rear of the system. So I tipped the top back down, and spun it around. Removed the rear panel and cleaned some more. (15 years of a lot of lint in there!) Then you'll need to remove the rear cover on the left side, covering the blower impeller. Get read for a whole lot of debris. Vacuum again. So now you have the motor exposed in the front and rear. You need to remove the impeller by turning that clockwise to loosen it. The trick is holding the shaft in place from the front at the same time. I used an old rag and wedged it into the impeller edges and worked it around until it jamed up. Once the rag was wedged pretty good, I went back to the front spun the shaft. Then you can remove the impeller by hand. Vacuum more. You may get by without having to remove the lint shoot completely, but I did just to clean it up more. I did have to remove two screws in the upper corner near the top of the lint shoot. (Basically the hold the back in place.) I took a few notes at this point about the wiring harness. Used a heavier screw driver (standard), You can push down on the clips that hold the old motor in place. Then work it out the front. Clean more. The new motor is not an exact replacement slightly differnt but the instructions with it were ok. Follow them for the correct wiring. You will need to remove one wire and cut and recrimp a spade lug or two. I used ty-wraps to secure the lines back in place. Look closely at the diagrams and make sure you set the motor down in the same direction the instructions say, if you twist it slightly it will sorta lock in place where it needs to be. Re-install the hold down clips to the front and rear of the motor. Clean up your impeller, and reinstall it too. Then basically reassemble the dryer...tracing your steps backwards. This isn't really difficult, it just takes time and as you can see, you will/should clean as you go !
Was this helpful?
Thank you for voting!
Dryer working but drum light not working, bulb ok.
22 of 27 people found this instruction helpful.
  • Denton from Indianapolis, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Problem: Drum light not working, bulb ok. Removed 6 screws on panel behind timer, light, buzzer, switches. Lifted back of dryer top then moved dryer top forward and off of dryer. The switch was located above the door. Unhooked wiring plug and took out 2 screws holding in the switch. Installed new switch and repaced bulb. Reassembled as ne eded and tested light by opening door. Works great.
Was this helpful?
Thank you for voting!
No heat
27 of 42 people found this instruction helpful.
  • Jaime from Chantilly, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Everything seems to work on the electric/gas dryer, but would not generate any heat. Did some research and ordered the thermal fuse & thermostat based on that. Replacement was simple and went well, however it did not fix the issue. Should have checked the continuity first as I found the "replaced parts" to be good. Have checked all ot her possible symptoms except the heating element, which requires addition labor. Overall, partselect portion was as advertised. All parts arrived quickly and were priced fair.
Was this helpful?
Thank you for voting!
All Instructions for the 110677
106 - 120 of 2659