110677 Kenmore Dryer - Instructions

All Instructions for the 110677
31 - 45 of 2659

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken tumbler belt
145 of 165 people found this instruction helpful.
  • Michael from San Antonio, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench set
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)
Was this helpful?
Thank you for voting!
Heating element burned out.
134 of 146 people found this instruction helpful.
  • Coleen from Chillicothe, OH
  • Really Easy
  • Less than 15 mins
  • Pliers, Socket set
After realizing that my dryer was no longer heating, I took off the back and examined the heating element. I saw that a coil was broken and knew that it needed replaced. When the part came in, I basically changed out the wires that were plugged into the old element on to the new one, replaced the screws in the heating element housing an d back panel, plugged in the dryer and was back in business! Oh, by the way...I am a 49 year old WOMAN!!!!
Was this helpful?
Thank you for voting!
When I opened my dryer door while it was running, the drum continued to turn and the light would not come on.
158 of 225 people found this instruction helpful.
  • Baxter from Goodlettsville, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First unplug your dryer. Then, I removed the two screws on the lint trap leaving the lint trap in place--do not pull out the lint trap--only remove the two screws. Next, slide the top of the dryer slightly forward in order to release the top of the dryer. I did this with my hands. Once the top of the dryer is released, raise the top of t he dryer and unplug the door switch assembly. Then, remove the two screws that hold the switch. These two screws were located on the front panel of my dryer and are visible when you open the dryer door. Remove the old switch and install the new switch by putting the two screws you previously took out from the old switch back in place and plug in the new switch. Lower the dryer top. Push the top back to lock in place. Line up the lint trap holes for the two screws that hold it in place and replace those screws. Plug your dryer back in and it should work properly. Very easy repair. We ordered our part one morning before noon, and it was here the next afternoon with regular shipping. GREAT SERVICE.
Was this helpful?
Thank you for voting!
Dryer was sqeaking loudly when running
125 of 147 people found this instruction helpful.
  • Edward from Andover, NJ
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set
I Looked on internet sites for this type of problem.
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I h ad also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.

Edward Brennan
Was this helpful?
Thank you for voting!
very loud squeeling sound
110 of 120 people found this instruction helpful.
  • jason from HOLDEN, MA
  • Really Easy
  • 30 - 60 mins
  • Socket set
The issue was the idler pulley. First I began opening up the front panel based on a youtube video but soon realized the model was slightly different and required a lot more items to remove. I saw the pulley in the back with nothing in the way so I put the front panel crap back on and removed the rear panel. There it was, very simple to re move and replace. I'm not looking forward to drum rollers though. Hopefully they're aren't as difficult as they appear.
Was this helpful?
Thank you for voting!
Broke start switch while moving
109 of 118 people found this instruction helpful.
  • Dennis from Port Orchard, WA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Turned off the power.Pulled the dryer out, removed the screws from the control cover panel, unplugged the switch, pressed the release clip the did the opposite to install new switch. Replaced the back panel, put the nob on and it looks as good as new.Turned on the power.
Was this helpful?
Thank you for voting!
dryer door would not stay shut
103 of 107 people found this instruction helpful.
  • Pam from Woodbridge, VA
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.
Was this helpful?
Thank you for voting!
Dryer had no heat and run forever.
126 of 185 people found this instruction helpful.
  • Robert from Scott, AR
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
after watching many videos on my problem and finding Partselect i read about others with same type issues and i decided to attempt my own repair.the first thing i did was go to home depot and buy a ohm meter around $10 then started testing all switches etc.first unplug the dryer then removed the rear panal and tested all circuits.my heati ng element tested bad so i removed it following the instructions from partselect taking about 5min.my heating element was broken.its funny but my dryer kept on running continually when it stopped heating,but the timer would move to the very end and just not quit.after reading on partselect i determined that my resistor not my timer was the problem.so i ordered the resistor without testing it first from partselect.turns out it was the problem now my dryer heats up fine and goes off like its supose to.i do advise to test things first like i should have but i just got lucky on the resistor.partselect is the only place i will buy from they are fast getting your part to you 2 days for me,and very cost effective.i spent around $84 including the cost of a ohm meter to repair my dryer which is 18 years old.beats the cost of replacing the dryer which i think many will agree.good luck on your repair hope this helped it was my first time ever repairing any home appliance.
Was this helpful?
Thank you for voting!
Make humming noise when pressing start button. Would not start
98 of 112 people found this instruction helpful.
  • James from Moscow, IA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
After looking on the website for advice I walked throught the simple steps of disassembling the front, removing the drum, removed the back, disconnected the wire harness. Then removed the blower housing in the back. The blower, mounted on the back side of the motor was very tight. I used a pipe wrench wedged in place and help by my 10 year old Grand-daughter while I used an adjustable wrench to turn the shaft on the front of the motor. Spun the blower off, removed the two clips holding the motor. Then reversed the process when I received the new motor. Care should be taken to avoid damaging the blower fan if a lot of pressure is required.
Was this helpful?
Thank you for voting!
Squeaky Dryer Noise
94 of 106 people found this instruction helpful.
  • Eddie from PELZER, SC
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
I purchased the dryer repair kit with the drum belt, wheels and idler pulley. I watched the instructional videos online and it seemed fairly straight forward. Breaking down the dryer and replacing the pulleys was easy enough. My problem began when I tried to feed the drum belt around the idler pulley. After finishing the job, the dryer wo uld not turn and the sensor light stayed on. I thought something else was broken with the dryer and spent hours trouble shooting other problems that I was having. Finally I figured out that the drum belt was not installed correctly around the idler pulley. However, I could not get it properly installed from the front of the machine so I tried from the rear still with no avail. I finally had to fish the old belt out of the garbage can that I had thrown away earlier. I lined up the old belt with the new one in the kit and discovered that the new belt was much smaller, so I put the old one back on the drum. Here's the lesson I learned...make sure the belts are the same size before attempting to install. The old idler was responsible for the squeaking and that stopped but I am still using the same old drum belt. Hope it lasts.
Was this helpful?
Thank you for voting!
door switch actuator spring broken
92 of 100 people found this instruction helpful.
  • Paul from Vero Beach, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
-unplugged appliance
-removed lint trap
-removed 2 lint trap shute screws with phillips screwdriver
-popped open top of appliance with standard screwdriver by applying pressure at each front corner so that it could be tilted up to access actuator switch on right side of door
-removed 2 actuator switch screws, located o n upper right side of laundry door, with phillips screwdriver (screws are accessed from outside of door frame not through appliance top).
-discarded broken actuator spring (accessed from open appliance top)
-replaced new actuator spring
-replaced 2 actuator switch screws
-closed top
-replaced 2 lint trap shute screws
-replaced lint trap
-plugged in appliance
-tested for operation
-kissed by happy wife
Was this helpful?
Thank you for voting!
Bought motor, then bought blower wheel also
95 of 111 people found this instruction helpful.
  • Daniel from Coatesville, PA
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers, Wrench (Adjustable)
couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!
Was this helpful?
Thank you for voting!
Broken belt - drum would not turn
87 of 101 people found this instruction helpful.
  • Gary from Oakland, MD
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcer ting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.
Was this helpful?
Thank you for voting!
Dryer lost heat but kept spinning
95 of 129 people found this instruction helpful.
  • Dave from Boise, ID
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Removed rear panel 10 screws, and heating element was situated on the right hand side of dryer and was held in place by two screws and had two heavy duty red wires connected to the element which were easily removed . Installing this item was a breeze .
Was this helpful?
Thank you for voting!
Very Loud Squeaking Noise
79 of 100 people found this instruction helpful.
  • GREGORY from Wilsonville, OR
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
1) Disconnected power cord from wall. 2) Disconnected vent hose from back of dryer. 3)Removed dryer rear panel. 4)Disengaged tension spring on idle wheel arm. 5) Removed worn idle wheel. 6)Installed new Idler wheel assembly. 7) Vacuumed dust from rear of dryer (optional, recommended). 8) Reinstalled rear cover, vent hose and power cord. E asy repair 15-30
Was this helpful?
Thank you for voting!
All Instructions for the 110677
31 - 45 of 2659