1106709701 Kenmore Washer Dryer Combo - Instructions

Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.

Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.

I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair

Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

I followed your short video and found it very easy to do

Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allow top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.

Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.

just followed the video directions, worked perfectly thanks

removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!

Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.

Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.

We got the part so fast we were both surprised. My husband installed the part by just seeing how the old one came off. It was simple and fairly quick. Except that his hands are so big they had a hard time fitting in to where the part needed to go. Just opened the top of the dryer, took the old part out and put the new one in.

Followed previous comments and took 5 minutes to replace. Be careful to hold spring and switch together because easy to separate and drop. Two screws to remove for switch, two to remove for lint trap, pop the lid up and switch / spring is easy to access.