110665 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Start switch didn't work, dryer ran when door closed
12 of 15 people
found this instruction helpful.
-
Robert from Corvallis, OR
- Really Easy
- 15 - 30 mins
-
Socket set
I removed 5 screws from the back of the top panel, removed the back panel, removed the start button from front of dryer, twisted the old start switch from the back, removed the two leads, reinstalled new part in reverse order. It was that simple! 15 minutes top. Dryer works fine. Gave me a chance to vacuum out all the dust bunnies and
... Read more
clean out the dryer vent pipe as well.
Thanks!
Thanks!
Read less
Was this helpful?
Thank you for voting!
Motor wore out
12 of 15 people
found this instruction helpful.
-
Charles from Clarissa, MN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I took the dryer apart ( using a repair book ) It was Super Simple to do I only needed a extra set of hand's to hold the drum in place while reassembling it. removed the hold down snap on collar's on the Motor ( after removing the Blower from the back of the dryer ( super simple. Extra set of hand's needed ) Reassembled in the same order.
... Read more
And now The Dryer work's like NEW..Shure Beat Buying a new Dryer..
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
There was no heat from the dryer
12 of 15 people
found this instruction helpful.
-
allen from perrysburg, OH
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
I watched the video on how to diagnose problem and then how to repair . Videos were very helpful. Also the parts were ordered on line and arrived in 2 days. Parts at a local appliance parts store were twice the cost of what I paid for the parts from PartSelect.
Other Parts Used:
Was this helpful?
Thank you for voting!
Drum would not turn and drum seal old
12 of 15 people
found this instruction helpful.
-
Geraldine from Stacyville, ME
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
Watch the utube video a few times. Followed instructions. Marked all screws. Cleaned the inside of dryer where motor is. Replaced drum seal and then belt. I replaced front of dryer screwed everything in place and I did it. Holding drum in place while installing front of dryer was hard as it was heavy but I did it m. My friends and husband
... Read more
couldn’t believe it. Utube is great!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
One of the drum support rollers was worn out
13 of 19 people
found this instruction helpful.
-
David from Fleetwood, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer stopped spinning
13 of 19 people
found this instruction helpful.
-
Danielle from FREEDOM, IN
- Really Easy
- More than 2 hours
-
Nutdriver, Screw drivers
The dryer quit working. I did some trouble shooting on your amazing site, ordered what i thought it might need and then got to work. Took no time to get it apart and replace roller kit and belt. What took the longest was getting in there and cleaning out probably 15 years worth of dirt and dust. If you have not opened your dryer up and d
... Read more
one this, 10/10 recommend, because in doing so i found that the motor was the real culprit. Once i opened it up more, especially cleaning around the blower fan and motor, i was half a day in. Put it all back together and got it running for two more loads before the motor quit. Replaced that and since the hard work was done, had it back in in half an hour and running great. Probably will need to redo the felt seal one day, but for now, i am calling it a win. This is my go to site for all things and i have been able to work on most of my major appliances and do it myself using the helpful information here.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Badly worn idler pulley and rollers.
11 of 14 people
found this instruction helpful.
-
TODD from GRASS VALLEY, CA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Braced dryer drum with a block. Removed the two rollers one at a time by using a screwdriver to pop off the triangular clip. Slid on new rollers. Would have been easier to remove the drum out the front instead of bracing it. Installed new idler pulley and belt. Dryer is 25 years old and sounds like a new one now when running.
Other Parts Used:
Was this helpful?
Thank you for voting!
broken clip on top panel hold down
15 of 26 people
found this instruction helpful.
-
Mark from Huntington Station, NY
- Easy
- Less than 15 mins
-
Screw drivers
pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.
Was this helpful?
Thank you for voting!
Dryer would not start
11 of 14 people
found this instruction helpful.
-
Daniel from Humboldt, KS
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Dryer would not start when the start switch was pushed. I was advised by the local repair shop to replace the "push to start switch" and the "thermal fuze". I unplugged the dryer and removed the back dryer casing which took all of 3 minutes. I removed the start switch and thermal fuze using directions on the whirlpool parts forum. This t
... Read more
ook maybe 5 minutes. I replaced with the new parts and put the casing back on the dryer. The entire project took 15 minutes. The dryer works perfectly. 34 USD for parts and shipping instead of 600 for a new dryer. Easy to identify the parts needed using the model number and the parts arrived the next morning I will use this company again for sure!
Read less
Was this helpful?
Thank you for voting!
Dryer does not turn off. Will stay in the Cool Down cycle
11 of 14 people
found this instruction helpful.
-
David from WINCHESTER, MA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
My dryer timer would run through the heat cycle and move in to the cool down cycle. It would not move past the cool down cycle, and would not shut off automatically. I tried replacing the Thermal Fuse first, since I'd already removed the back panel to diagnose the problem. There was no change - the dryer did not shut off automatically. Ne
... Read more
xt, I removed the back cover to the timer console. The Timer Power Resistor looks like a black circle and a rectangle joined together. It was attached to the back of the on/off switch by a single hex head screw, and the resistor has orange and black wires attached. The replacement Power Resistor doesn't look like the resistor that was in my dryer. It is rectangular in shape with 2 male spade connectors. I attached the orange and the black wires to the new power resistor. I started the dryer and it went through a full heat/cool down cycle, and automatically shut off with the end of cycle buzzer sounding. Total part replacement time was about 10 minutes.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
No heat on any applicable settings
9 of 9 people
found this instruction helpful.
-
Russell from LOUISVILLE, KY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Cleaned entire unit, replaced all thermostat assemblies and exhaust seal
Other Parts Used:
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people
found this instruction helpful.
-
Dawn from Chesapeake City, MD
- Really Easy
- Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
Lint remover was worn and completely fell apart
9 of 9 people
found this instruction helpful.
-
Debby from Wellesley Hills, MA
- Really Easy
- Less than 15 mins
I didn't think I could find a replacement part because the dryer was so old (it has fake wood paneling!) and I was already considering the cost of a new dryer. I searched online and found this site. I crossed my fingers and placed my order. When it came, I removed what was left of the old lint remover and put in the new one. It was a perf
... Read more
ect match. The colors were a bit off but who cares. PartSelect saved me from having to purchase a new dryer. Yay!
Read less
Was this helpful?
Thank you for voting!
dryer kept running when door was open
11 of 15 people
found this instruction helpful.
-
Dean from New Bern, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
changed out the switch. easy. about 20 minutes. part came quickly (2-3 days). great service. thanks.
Was this helpful?
Thank you for voting!
Replaced a broken pulley.
10 of 12 people
found this instruction helpful.
-
Brian from IMLAY CITY, MI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.
Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
Was this helpful?
Thank you for voting!