1106613 Kenmore Dryer - Instructions

Called my youngest son and had him do. He said he watched a U-tube on his pc for installing instructions

Opened the cabinet and removed the drum. Cleaned out the dryer fuzz. found that the roller stabilizer wasn't in place; apparently due to a previous repair. Replace both rollers and the roller stabilizer and prepared to replace the drum. But because I live alone, I didn't have anyone to hold the drum while I connected the belt to the motor ... Read more . But, I did have three unused balloons which I partially inflated and set the drum on them in the bottom of the cabinet while I hooked up the belt to the motor. Put everything back together and it is now drying my clothes again. :)

Followed the video and it was perfect. Easy repair that took under 15 minutes. Great, clear process that was perfectly easy.

First I viewed the video detailing the repair. The video illustrated to steps to replace the part very well. I opened the top of the dryer to gain access to the part, replaced the part and closed the top. All done in less than an hour.

Followed instructions on web site video. Made repair very easy.

My son did the repairs it took less than 30 minutes it's an old dryer so glad to be able to get the parts. I do not like the new dryers because of all the pushbuttons thanks so much for the ports

I followed Steve's instructions from the video. 1. Unplug dryer. 2. Remove lint catcher. 3. Unscrew the two screws there and put screws to one side. 4. Release catches holding top of dryer and put top of dryer back against the wall. 5. Open dryer door and remove two screws holding the door switch that needed replacing, putting screws into ... Read more the dryer. Remove switch. 6. Put in new dryer switch and put two screws back in to hold it. 7. Replace top of dryer, making sure catches are secure. 8. Put two screws back into lint filter area. 9. Replace lint filter. 10. Put plug back into the wall. Voila! The dryer light works and the dryer stops when I open the door during the cycle.

The repair was simple. The plug must be pried away from the connection with a pocket knife or small flathead scew driver.

Disconnect Dryer. Remove Screws of lint trap (2). Slide Dryer Top (Cover) and push up to disengage the plastic clamps. Remove the two screws of the old switch (located inside the door panel - upper right side). Disengage the old switch and fasten the new one. Repeat steps backwards to tight new switch and place the dryer cover.

Googled the symptoms the cure was replace the motor. There was a video done by parts select that made the process even easier. Had it done in about 25 minutes.

An online video provided perfect instructions. Unplug the dryer. Remove the Lint filter and see two Phillips screws located on the top of the machine, then remove the screws. Then slide a stiff, thin putty knife under the right front corner between the top and the front panel. The clip inside has small feet holding it in place, so you ... Read more need to angle the putty knife up slightly, then push in towards the back of the dryer while lifting up on the top. The corner will lift away from the front. Repeat the process on the other front corner. Now lift up the top that is hinged at the rear. I used a 24" 1 x 2 board to keep the top up. Open the front door and remove the two screws that hold the switch in place then unplug the switch on the inside of the dryer and remove. Plug in the new switch (2 or 3 wires may be present, but it doesn't matter). Attach the new switch using the two screws you removed. Lower the lid and tap each front corner to reengage the clips, then put the two screws back in at the lint filter. Replace the filter, plug the dryer back in, and you're done. I honestly think that it took longer to type these instructions than it took to do the actual repair.

I thought I had checked the arm piece of the rack real good for a product number on my original part but I missed the number till the 2nd box came in, and a looked real careful and realized it was the same as the order I thought was bad.
Put the spring arm in first and the rack will fit in the front groove.
It would have bee ... Read more n good if there had been a picture of the dryer arm attached to the dryer.
So I have 2 good racks and will return one if you tell me where to send it.
Keith Walden..

followed the enclosed instructions, used a balled up towel to support the drum while attaching the belt and tension pulley, took about 20 minutes

followed the repair video .. unplug dryer ... removed screws on lint trap .. popped the top off the dryer .. removed the two screws on the switch ..unplugged the switch using a small screw driver .. replaced switch .. put it all back together .. it took about 20 minutes

First you disconnect electricty then gently pry up the top of dryer with a flat screwdriver. You will find a three wire plug unplug wire and take the two phillip screws our of the switch lift our the switch and reverse the prossess to reinstall new switch