1106613 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drum would not turn. Broken Belt
5 of 10 people
found this instruction helpful.
-
Ray from Boulder Creek, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed top cover. Removed front cover. Removed Drum. Located the broken belt. Found that there was no tensioner in the unit. Replaced drum rollers. Put in new tensioner. Repaced Drum with belt around it. Installed belt through tensioner and onto drive pully of motor. Supported Drum with wood block. Turned on dryer to insure drum turned w
... Read more
ithout any problems. Removed wood block. Replaced front cover and top cover. Repair compete.
Read less
Was this helpful?
Thank you for voting!
Bad Motor, Would not start.
3 of 5 people
found this instruction helpful.
-
Steve from S LAKE TAHOE, CA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very
... Read more
tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.
Read less
Was this helpful?
Thank you for voting!
The original motor stopped working
2 of 2 people
found this instruction helpful.
-
Robert from PFLUGERVILLE, TX
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexib
... Read more
le dryer tube since the old one had a few holes. It works perfectly again.
Read less
Was this helpful?
Thank you for voting!
Loud screeching when dryer tumbles
2 of 2 people
found this instruction helpful.
-
Joan from MANLIUS, NY
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
We had to pop open the top. Unscrew front of dryer from sides. Disconnecting the wires was a bit more difficult than expected. We had to use a tiny screwdriver to slide into the sides of the white wire connector on each side before pulling apart. Front drum falls when front of dryer is removed. It took two of us to reassemble - one to hol
... Read more
d the drum while the other put the front on. Our problem turned out to be one wheel. We replaced both wheels and saved the rest of the parts. Hums along just fine.
Read less
Was this helpful?
Thank you for voting!
dryer won't start
2 of 2 people
found this instruction helpful.
-
ALEX from ELMSFORD, NY
- Really Easy
- 30 - 60 mins
1. Didn't understand how to do continuity test for 3-wire door switch. After looking that up, I discovered that wasn't the problem ! I have tested, the thermal fuse, oscillating fuse,start switch, I've tested the timer and the black , blue connections go to zero ( continuity good) the tan , white connections just barely off of infinity
... Read more
. I've ordered a new timer. I'll let you know if that's the problem. If you can more diagnostic videos. AKH
Read less
Was this helpful?
Thank you for voting!
drum made a thumping sound was really noisey
3 of 5 people
found this instruction helpful.
-
james from auburn, IN
- Really Easy
- 30 - 60 mins
-
Nutdriver, Socket set, Wrench (Adjustable)
pulled dryer away from wall took screws out of lint screen lift top removed 2 screws one on each side of front at top and removed front panel. pulled belt off drum removed drum rollers tension pulley and while i was at it pulled back cover off of heating element and blower blew everything out with air hose did a total cleaning installed e
... Read more
verything in reverse. i was amazed how fast the parts came the dryer was only down 2 days and it runs like new even if it is 20 years old i highly recommend parts slect and i will use them in the future
Read less
Was this helpful?
Thank you for voting!
Loud rumble and finally the drum stopped because the belt broke
3 of 5 people
found this instruction helpful.
-
William from Rocky Mount, VA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I opened the top and front of the dryer. 1st I pulled out the drum and cleaned up the lint and mess from the busted support roller. Next it was a matter of looking at the enclosed drawing and instructions. I could not believe it was that easy.
Was this helpful?
Thank you for voting!
Handle on dryer door broke.
2 of 2 people
found this instruction helpful.
-
Kevin from GRESHAM, OR
- Very Easy
- Less than 15 mins
The part arrived in the mail. I used a pair of kitchen scissors to open the package. I removed the part from the plastic bag, and snapped it into place on the front of the dryer. Total time: 15 seconds.
I wish all my repairs were this easy.
I wish all my repairs were this easy.
Was this helpful?
Thank you for voting!
Dryer wouldn't turn on.
2 of 2 people
found this instruction helpful.
-
Linda from SANTA MONICA, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
Noticed the door switch was loose and the light bulb inside dryer didn't stay on. Researched the problem on PartSelect. Followed the directions given: Take 2 screws out of top of lint trap. Pry top off of dryer with putty knife. Unscrew 2 screws in dryer door frame holding in old switch. Uplug and remove old switch. Plug in new swi
... Read more
tch and put screws back in. Close top of dryer. Reinsert 2 screws in lint trap. My 20 yearn old dryer works!
Read less
Was this helpful?
Thank you for voting!
Light wouldn’t work and dryer wouldn’t stop when you open the door.
2 of 2 people
found this instruction helpful.
-
Karen from HUNTSVILLE, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove the lint screen, then remove the two (2) Phillips screws that are at the entrance of the lint screen compartment. Take a putty knife and insert it under the top pannel of the dryer about 1” in from the outside and push the putty knife in as you lift that corner of the pannel. Repeat on the other side. Then raise the lid and prop it
... Read more
up. The door switch is on the right side just behind the door on the inside. Open the door and remove the two screws that hold the switch and remove the switch. Install the new switch like the old one came out and close it up you’re ready to go! It is very easy you can’t hurt anything.
Read less
Was this helpful?
Thank you for voting!
plastic handle broke
3 of 5 people
found this instruction helpful.
-
Mary Jane from WESTHOFF, TX
- Very Easy
- Less than 15 mins
Replacement handle snapped right back in place. Took about 2 seconds.
Was this helpful?
Thank you for voting!
handle broke off
3 of 5 people
found this instruction helpful.
-
Arlene from BOYNTON BEACH, FL
- Very Easy
- Less than 15 mins
followed simple directions and it took 1 minute! Lime up with the hole and gently push, it clipped in immediately! You are a great place to go to for repairs!!!
Was this helpful?
Thank you for voting!
Broken handle
3 of 5 people
found this instruction helpful.
-
Richard from WASHOUGAL, WA
- Very Easy
- Less than 15 mins
removed and replaced door handle no tools required
Was this helpful?
Thank you for voting!
Dryer would not turn on.
2 of 2 people
found this instruction helpful.
-
RICHARD from LEVERING, MI
- Very Easy
- Less than 15 mins
-
Screw drivers
I just followed the instructions from this site for the door switch part and had it running in 10 minuets. This site made it very easy.
Was this helpful?
Thank you for voting!
Broken door catch on dryer door
2 of 2 people
found this instruction helpful.
-
Anthony from NORTH ADAMS, MA
- Very Easy
- Less than 15 mins
-
Screw drivers
Gently remove the door bezel by prying it off with a small screwdriver. Then remove the door catch from the door with the same screwdriver. Be careful not to drop it in the door. I did and had to fish it out with a small hooked pick. Install the new door catch by sliding the top in first then the bottom. Again, careful not to drop it in
... Read more
the door. Then snap the door bezel back in place.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!