1106613 Kenmore Dryer - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I raised the top of the dryer, removed the front, the belt and the drum. Slipped off old rollers, installed new ones and new tensioner. Reinstalled drum and belt, bolted front back on and closed the top.

it took loess than 10 minutes to change the door switch after watching the repair video

Partselect order confirmation email included video instructions of how to change the door switch on my model dryer. Like others I had a pause with the switch connector. I viewed the video again and the instrucions showed to use the putty knife tip to push down on the connector tabs and it came right off. Replacing the switch was easy a ... Read more s the video instructions. Fast shipping of the right part at a good price. The video was pricless. Thank you partselect.

I typed in on my brouser Repair Kitchen Aid Dryer door switch.
And on You Tube up came several videos showing me how to ewmove the switch and install the new one.

The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away fro ... Read more m the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada

Just popped it into place needing no tools at all. Took less than a minute.

Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to ... Read more take the time to remove dust and lint from behind the dryer. Easy repair.

Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.

Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.

Just follow the instructions the one was provided with Maitanace kit we bought from you.

I disassembled the dryer once to clean the motor and compartment. After reasembly, the problem persistes. I ordered the motor and the second diasasssembly was accomplished in 10 minutes and the entire job took 45 minutes and the dryer was running like new. Tip- Leave the motor secured while removing the blower fan.

Used the screwdriver pressed the blade against the edge of the door catch and popped it out. Put the new door catch in place and pressed it and it snapped into place. Done

Removed the plastic guard. Snapped the catch in place and replaced the guard

Unplugged washer,removed the two screws by the lint trap,moved the top foward lifted the top (it'shinged in the back )the switch is right inside the door top right hand corner removed the two screws that hold the switch in place used a flatblade screwdriver to seperate the connections pulled off the old installed the new switch put every ... Read more thing back together worked as though it wes never broken

I received the part and was able to get this on my dryer in just a few minutes. I would use this company again if I have any issues with my products at home.

I looked at the parts breakdown to see how it cam apart.

I tore the dryer down,
1. removed the door
2. openned the top
3. removed front panel
4. removed fron bulkhead
5. removed belt and drum
6. removed back cover
7. removed the ductwork
8. removed the fan (this is ... Read more the hardest part, it is very tight on the motor with left hand threads, there are flats on the (inside of the dryer)fan where the motor shaft goes into the fan for a wrench and you can put a socket on the front pulley on the motor. I ended up just knocking the center out of the fan and replacing it.
9. removed the motor and cleaned the entire unit
10. reinstalled everything in reverse order. Note:I went ahead and replaced the idler pulley and the rear wheels that support the drum, and put a new belt in (just about
everything that could fail) I spent about $200 to keep a $1200 dryer in service at least another 7 years.