1106603301 Kenmore Washer - Instructions

The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's press fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you

Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.

Ordered a new Faucet Adapter! Simple

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.

Replaced the faucet adapter, works fine

two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clothes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened

I noticed that the dryer door switch actuator spring/lever was broken on the door. I researched how to get the top of the dryer cover off, and I took apart the mechanism. I called a local repair shop and they wanted me to buy the whole unit instead of just the switch lever. So I did some research to find the part on the web, and I came across your site. It was very easy to navigate, and I fould the part easily. I saved about 66% by just ordering the lever and not the whole unit. I would without hesitation, buy parts from your website again. The part was shipped and received very quickly. Thanks again!

I went to internet & got the part & instructions.the shipping cost more than the part. Saved 20.00 & gas.

I thought it might be a damaged switch but when I removed it I noticed a metal clip that was attached to it was broken. The pin on the door pushes against this clip when the door is closed which in turn opens the circuit on the switch. I looked up the model on this website and viewed the parts diagram. There I saw the part I needed and it was listed below along with the cost. Couldn't of been easier. Thanks!

I unsrew the faucet head, and attached th e adapter

replace the water valve

Removed the old one installed the new one