11065132410 Kenmore Dryer - Instructions

Installed thermal cut-off kit. Dryer works fine now. Kit very easy to install.

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

put the high limit in , plus the temperature , plus the exhaust switches

I followed disassembly directions found on youtube and replaced th two-piece ring bearing that was identified by a parts diagra fron PartSelect. The repair was easy. Fix time was about thirty mionutes.

removed the back housing of the dryer and located the thermal switch. unscrewed the old one, popped in the new one and whala! I was back in business!

put the back cover back on the dryer and pushed it back into place.

first i removed the back cover by removing the six 1/4 inch screws then i removed the wires to the thermal switch there were three of them and using an ohm meter i checked each one for continuity until i found the one that had an open circuit. i removed the two 1/4 inch screws holding it in place and replaced it with the new one.

I first unplugged the dryer and pulled it away from the wall. I had to remove the vent tubing to gain access to the rear of the unit, then removed the screws on the back panel of the dryer. I took off the panel and noticed that lint that had gathered over the years around the back of the dryer. I vacuumed it clean then proceeded to problem solve. I noticed four easily identifiable areas, the thermal cut-off switch and thermostat located by the heating coil and the thermostat and fuse near the venting area. I first checked the fuse with a ohm meter, it was okay. I removed each component one at a time and created a bypass with a alligator clip wire. Plugged the dryer back in to determine if heat was produced while testing each area one at a time. I determined that heat was produced after bypassing the thermal cut-off switch. I then ordered the thermal cut-off switch kit (arrived within 3 days) and installed it within 20 minutes. The longest time spent was trouble shooting, the removal and installation was very easy. By the way, I did use the ohm meter to check the resistance across the thermostats as indicated in previous postings, but I found the results and technique to be more confusing. A bypass worked the best for me and much more reliable. The heat started immediately. I highly recommend downloading the schematics of your unit for part number and location identification.

they sent the wrong part . when i got the right part i removed the two screws holding the element . took the Thermostat out . removed the plugs . put the new thermostat in plug in the plugs. screwed the element back in place . And now i need to replace the fuse located at the top of the element casing.

Took dryer apart. Should've started with You tube videos so I took more apart than I needed.

Got all the parts I needed from Parts select.

Fixed it and works great.

I shorted the thermal cutout after removing the back.
I then ordered the thermal Cut-Off Kit from PartSelect.
While this was not my first order from them, I was still impressed with the ease and by how soon I received the part without any hassles or glitches. PartSelect will be my primary parts supplier from now on.

i took a stab that it was the thermostat,but it wasn't.after finding out it was the coils i purchased them and lifted the top of the dryer and undid two screws in the upper front of the dryer and lifted the front off all while holding the tub in place.The coils are located in the very front left of the dryer,i took the holder bracket off,disconnected the wires and replaced the coils(they just sit on a rod)dryer works like new and thanks to the new thermostat also gets hotter,i'm guessing that was next.

From the front, taped part in place and then assembled springs and insulator from the rear. Difficulty occurred with access to the back of the sensor due to the air duct interference. The sharp edges of the sheet metal parts increases the risk of cuts. First shipment was missing the second electrode but Part Select immediately replaced the shipment. My experience has to be considered Excellent and I would go to Part Select first for my next order.

Looked on YouTube and found these guys. Followed their instructions and no problem.

I watched the video then called them to order parts. They were VERY helpful & NICE. I had the parts the NEXT day. I followed the video instructions & it worked. They made my day! THANK YOU JoAnn & Teresa!

removed door and front panel this exposed all the control devices I changed out the thermostat ndn repaired the dryer